Top-rated concrete cutting pros.

Get matched with top concrete cutting pros in Rogers, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Rogers, MN?

Select your specific project to find the pro for you.

TRUSTED BY ROGERS, MN HOMEOWNERS

  • Average homeowner rating star icon4.5
    Average homeowner rating
  • Verified reviews icon252
    Verified concrete cutting services reviews

Find Concrete cutting pros in Rogers

Avatar for Trinity Landscaping & Excavating Inc
Trinity Landscaping & Excavating Inc
4.8(
177
)
Concrete Flatwork - Repair & Resurface

Serving Rogers, MN and surrounding areas

Approved

In business since 2000

Free estimates

Emergency services offered

"We couldn't be happier! Travis and his crew did a great job on our patio. It looks great and we have had lots of compliments from neighbors. Having a small backyard, we appreciated that Trinity used smaller-sized equipment to minimize the damage. They were helpful with the design and resolved some grading issues that had resulted in water in our garage each Spring. The key differentiator for us was the integrity and honesty of the company. We never felt like Trinity was trying to cut corners. In fact, there were a couple of days where they were on-site to perform a task (e.g. cutting control joints) and they chose to delay and make an extra trip because the concrete wasn't ready. It would have been easiest for them just to perform the task since they were already on-site, but they chose to delay in the best interest of our project. And...Trinity was actually one of the lower bids we received for this project."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+50

Response time1 day
Response rate100%
1 neighbors recently requested a quote
Avatar for American Waterworks
American Waterworks
4.5(
173
)
Concrete Flatwork - Repair & Resurface

Serving Rogers, MN and surrounding areas

Approved

In business since 1989

Free estimates

Warranties offered

"Quoting was fair and easy. There was a bit of a mix up between the quote and the person's doing the work, but was resolved fairly quickly the work was done just as quickly. Our concrete was raised noticeably and our issue resolved at the time of the work. They have a great warranty, which should be considered with every job in my opinion, it's a fair price for peace of mind! Would use again and have already pass along a referral!"
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
563 neighbors recently requested a quote
Recommended by91%of homeowners
Avatar for Gardner Construction Inc
Gardner Construction Inc
4.6(
346
)
Concrete Flatwork - Repair & Resurface

Serving Rogers, MN and surrounding areas

In business since 1996

Free estimates

Warranties offered

"Seth responded in a timely manner, proposed several ways of solving the problem, and offered additional suggestions to help with the drainage around the stairwell, which was the source of the original damage. He was willing to look at the project holistically, and knowledgable on all aspects of the job. Many concrete companies will limit their involvement to only the concrete work itself, but most projects are rarely so clear cut. We had a portion of the wall rebuilt with new block, new rebar, and a finish parge coat. Railings were removed and reinstalled. The grade was modified using new fill, new river rock and edging."
Our team created a trench to the footings and filled it with a drain pipe and rock to channel the water to the sump pump.
This is the front of the steps, before the Gardner Construction team resurfaced the steps and replaced the sidewalk.
This homeowner wanted to replace the window and needed to repair the cracked and crumbling foundation.
The Gardner Construction team installed a new glass block window, providing additional security and a vent, and repaired the foundation.
After installing the sump pump and the drain tile system, our team repours the concrete.

+18

Response time3 days
Response rate100%
Recommended by96%of homeowners
Avatar for The Original Driveway Design
The Original Driveway Design
4.4(
109
)
Concrete Flatwork - Repair & Resurface

Serving Rogers, MN and surrounding areas

In business since 1977

Free estimates

Warranties offered

"Received a visit from the estimator the same day I called. That person stated the work could not be done because the curb cut was on city property/easement. I called the City of Robbinsdale who stated WITH a permit, the work can be done. The estimator, with 20 years of experience as he stated, clearly was not familiar with city permits. I was disappointed. I have hired someone else."
Asphalt
StreetPrint
Concrete
Response time3 days
Recommended by95%of homeowners
Avatar for Greene Construction Inc
Greene Construction Inc
4.4(
107
)
Concrete Flatwork - Repair & Resurface

Serving Rogers, MN and surrounding areas

In business since 1989

Free estimates

Emergency services offered

"The installation went great.  I had no issues contacting Green Construction to schedule the work or for any questions I had. 
I wanted a egress window put in for a downstairs bedroom, the existing window was not a egress.  The crew had to cut into my driveway to dig the hole for the well. The cut was precious and they didn't tear up my driveway.  The workers were very professional and they did a great job.  The window and especially the timber well look great.
I would recommend green construction to anyone wanting a egress window.
"
Recommended by94%of homeowners
...
Showing 1-10 of 80
Concrete Cutting questions, answered by experts

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

To maintain custom or fabricated metal structures and extend their lifespan and appearance, perform regular cleaning, apply rust prevention treatments, and use protective coatings.

The Rogers, MN homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.