Top-rated contractors.

Get matched with top contractors in Moreland, ID

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Moreland, ID?

Select your specific project to find the pro for you.

Find Contractors in Moreland

Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Moreland, ID and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Moreland, ID and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for Black iron construction
Black iron construction
5.0(
6
)
Major Home Repairs (General Contractor)

Serving Moreland, ID and surrounding areas

In business since 2021

Free estimates

"Ryan Seminario/Black Iron Construction installed a sliding door package in our living room. It was difficult to find someone willing to do a smaller project but Ryan was totally on board. This project required installing a header and re-constructing the wall to fit the doors, putting up drywall, sanding and texturing the wall and putting up new siding on the outside. He did a beautiful job! He paid attention to detail and got everything right. He is very good about communicating. Especially when he will be on site and what he will be working on. When he wasn't comfortable doing the wiring needed for our project, he was honest and upfront with me. We worked together and found an electrician to do it. He put up a plastic wall around the work area and cleaned the work area at the end of each day. I really appreciated that! I highly recommend Black Iron Construction for any project."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+6

Recommended by100%of homeowners
Showing 1-10 of 25
Unfinished Carpentry questions, answered by experts

Yes, using certified lumber and engineered wood products for reduced environmental impact.

To calculate the number of linear feet of baseboard you’ll need, measure the length of each wall of the room you’re installing them in as close to the floor as possible, rounding up to the next full linear foot. If it’s your first DIY molding job, having a few extra feet on hand for miscuts is a good idea.

While some highly experienced homeowners can frame a house independently, it is not advisable. You will need ample carpentry experience, a team of helpers, and professionals to sign off on your work to meet local building codes. For the safest outcome, we recommend buying or building a house with the guidance of professionals.

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

A cross brace for a fence gate should stretch from the top corner of the gate’s hinge side to the bottom corner of its latch side at a 45-degree angle to the bottom of the gate. This positioning distributes the bulk of the gate’s weight to the base of the post, taking pressure off the top hinge.

The Moreland, ID homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.