Top-rated contractors.

Get matched with top contractors in Morenci, AZ

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Morenci, AZ?

Select your specific project to find the pro for you.

Verified Reviews for Contractor Service pros in Morenci, AZ

*The Angi rating for Contractor Service companies in Morenci, AZ is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Contractor Service needs.

*The HomeAdvisor rating for Contractor Service companies in Morenci, AZ is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Contractor Service needs.

Last update on December 31, 2020

Find Contractors in Morenci

Avatar for HCP Restoration, LLC
HCP Restoration, LLC
5.0(
7
)

Serving Morenci, AZ and surrounding areas

Approved

In business since 2020

Free estimates

Emergency services offered

"Condensate line was leaking in kitchen wall. Had to remove half of kitchen to get to problem. They found the leak, repaired, remediated and then restored! Kitchen is as good as new!"
Response time8 hrs
Response rate100%
1 neighbors recently requested a quote
Request Quote
Avatar for Homemade Design
Homemade Design
3.7(
322
)

Serving Morenci, AZ and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Request Quote
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)

Serving Morenci, AZ and surrounding areas

In business since 2006

Credit card accepted

"They did a good job. She had to submit like a photo but my daughter had them work on the central are of the loft. The deal was for one room. She got a lot of good ideal from her and it was worth it for her. They were professional and I did not hear anything negative."
Recommended by55%of homeowners
Request Quote
Avatar for Tim Ehlers Dba Patriot roofing
Tim Ehlers Dba Patriot roofing
3.8(
34
)

Serving Morenci, AZ and surrounding areas

In business since 2006

Free estimates

Emergency services offered

"Tim Ehlers DBA Patriot Roofing suggested that we go back to the company that actually put the roofing material on. He did not take advantage of the situation. Everything went efficiently. My husband had the main conversation with him and it wasn't a lot of time off of my husband's schedule, because I think he came from work to stop and visit with him. It seemed to go well."
Hail
Recommended by73%of homeowners
Request Quote
Unfinished Carpentry questions, answered by experts

The easiest way to tell if a wall is load bearing is to check if it’s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don’t fit into these categories can still be load-bearing. If you’re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.

Your local building code will list all the framing requirements for whatever type of structure you're building. Most exterior walls require spacing of 16 inches on-center, while many non-load-bearing interior walls only require 24 inches of spacing. However, there are also varying requirements depending on your construction material, so checking your municipality's rules is essential.

An A-frame home can be cheaper to build than a traditional house, but that is not always a given. Prices can be fairly similar in some cases, depending on the location, design, and necessary site preparation. Costs for an A-frame typically run between $100 to $200 per square foot, which is comparable to the cost of a traditional home. The cost of an A-frame can come in under those numbers if you opt for a prefabricated kit.

Metal stud framing parts include the studs themselves, upper and lower tracks that act as top and bottom wall plates, various angle fasteners and clips, screws for fastening pieces togeher, metal straps, c-channel supports, and thicker steel supporting structures. Roof framing metal components include pre-fabricated trusses, heavy-gauge stud pieces, and various plates and fasteners.

Yes, you will need a jack for a rim joist replacement. To prevent sagging and facilitate the removal of load-bearing wood, you’ll need to relieve the pressure from this joint before beginning work. 

Due to hydraulics and other specialized equipment, a sill plate and rim joist replacement are not typically a DIY project. Hiring a professional structural engineer and experienced contractors is the best approach to replacing rotted sill plates and rim joists.

The Morenci, AZ homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles