Top-rated concrete cutting pros.

Get matched with top concrete cutting pros in Readstown, WI

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Readstown, WI?

Select your specific project to find the pro for you.

Verified Reviews for Concrete Cutting pros in Readstown, WI

*The Angi rating for Concrete Cutting companies in Readstown, WI is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Concrete Cutting needs.

*The HomeAdvisor rating for Concrete Cutting companies in Readstown, WI is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Concrete Cutting needs.

Last update on August 20, 2026

Find Concrete cutting pros in Readstown

Avatar for American Waterworks
American Waterworks
4.5(
171
)
Concrete Flatwork - Repair & Resurface

Serving Readstown, WI and surrounding areas

Approved

In business since 1989

Free estimates

Warranties offered

"They did great. The entire surface was level and free from tripping hazards. It is important to have them seal the cracks because there will be water from snow melt and the concrete will move. This will get you the 5 yr warrantee just in case."
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
640 neighbors recently requested a quote
Recommended by91%of homeowners
Request Quote
Avatar for NextGen Concrete
NextGen Concrete
5.0(
2
)
Concrete - Sawing or Removal- For Business

Serving Readstown, WI and surrounding areas

In business since 2024

Free estimates

Small jobs welcome

"Very happy with our shop floor. It is sloped to the drain perfectly. They were reliable and when figuring how much concrete would be needed, they barely had any extra! Great people to work with!"
ICF Foundation
Basement floor
Response time2 hrs
Request Quote
Avatar for R2R Concrete
R2R Concrete
5.0(
1
)
Concrete - Sawing or Removal- For Business

Serving Readstown, WI and surrounding areas

In business since 2023

Free estimates

Credit card accepted

We pride our company on reliability, great communication, integrity, and quality work. We are experts in our trade and will do our best to keep you as educated as we can on your particular task or project. We look forward to earning your business! Book with us online or feel free to give us a call today!\n

Response time2 hrs
Recommended by100%of homeowners
Request Quote
Avatar for Stone AXE
Stone AXE
New to Angi
Concrete - Sawing or Removal- For BusinessConcrete Flatwork - Repair & Resurface

Serving Readstown, WI and surrounding areas

Free estimates

Emergency services offered

Warranties offered

I’m a very dedicated person and take pride in my work, I’m very focused on msking my customers satisfied, and always finish the job with a happy customer,

Full house remodeling
Full house remodeling
Full house remodeling
Full house remodeling
Full house remodeling

+1

Request Quote
Concrete Cutting questions, answered by experts

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

The Readstown, WI homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles