Top-rated stucco pros.

Get matched with top stucco pros in Algoma, WI

Enter your zip and get matched with up to 5 pros

Find Stucco pros in Algoma

Hip & Ridge Construction
4.5(
6
)
Synthetic Stucco - Install or Completely ReplaceSynthetic Stucco - Install or Completely Replace- For BusinessSynthetic Stucco - Repair or Partially Replace- For Business+4 more

Serving Algoma, WI and surrounding areas

In business since 2011

Free estimates

Credit card accepted

"The roofers were extremely professional and nice. They found that the previous roofers did not put flashing around the skylights. All of the wood around them was rotten. They had to take all six skylights out to replace the wood. They did it with minimal dust inside. They took the time to put extra ice and snow barriers around the skylights. They went above and beyond. I would recommend Brian and his crew to anyone. Todd from Hip and Ridge Construction is friendly, professional and honest."
Recommended by100%of homeowners
Stucco Repair and Son
New to Angi
Synthetic Stucco - Install or Completely Replace- For BusinessTraditional Stucco - Install or Completely Replace- For Business

Serving Algoma, WI and surrounding areas

In business since 2021

Free estimates

Credit card accepted

Stucco Repair and Son is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests and make their concerns the basis of our business.

JC Elevation Team
New to Angi
Synthetic Stucco - Install or Completely ReplaceSynthetic Stucco - Install or Completely Replace- For BusinessSynthetic Stucco - Repair or Partially Replace- For Business+4 more

Serving Algoma, WI and surrounding areas

In business since 2022

Free estimates

Offers commercial services

JC Elevation Team is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers interests, and make their concerns the basis of our business.

Stucco questions, answered by experts

When cleaning stucco siding, it is recommended to use a pressure washer with a psi (pounds per square inch) between 1,500 and 2,000. This range provides sufficient power to remove dirt and grime without causing damage to the stucco surface. It's important to avoid using excessive psi as it can chip or crack the stucco. 

Using a wider spray nozzle and keeping a safe distance of about seven to 10 feet from the siding helps ensure a gentle and effective cleaning process. Always follow the manufacturer's guidelines and adjust the psi accordingly based on the condition of your stucco and the specific requirements of your pressure washer.

Yes, you can apply the stucco yourself, but it is a time- and labor-intensive project, especially on the exterior of a whole house. DIY stucco is better suited for repairing stucco siding or siding a smaller building, such as a shed or garage. Since most of the cost of stucco siding goes to labor, you can cut down significantly on the total if you’re up for the challenge.

Yes, you can screw directly into stucco. Only do so if the item you are installing is a permanent fixture. Drill a pilot hole into the stucco using a masonry or concrete bit, then drive in the screw with a power drill or screwdriver.

German schmear is a durable brick masonry coating. It should last at least a decade or two without flaking or fading, even with minimal maintenance. This makes it an economical option compared to the cost of painting your house exterior, which usually needs to be repainted every five to 10 years to keep it looking its best—thus costing more over the same time period.

You can use small bits that are up to 3/8 inch in diameter, or larger bits that are 1/2 inch or more in diameter. Make sure the bits you use are coated with carbide or diamond; this information is usually visible on the package. You can also use hole saw bits to drill into stucco.

The Algoma, WI homeowners’ guide to stucco services

From average costs to expert advice, get all the answers you need to get your job done.