Top-rated drywall insulation pros.

Get matched with top drywall insulation pros in Brier, WA

Enter your zip and get matched with up to 5 pros

Need a pro for your drywall insulation project in Brier, WA?

Select your specific project to find the pro for you.

TRUSTED BY BRIER, WA HOMEOWNERS

  • Average homeowner rating star icon4.7
    Average homeowner rating
  • Verified reviews icon1.1k+
    Verified drywall insulation services reviews

Find Drywall insulation pros in Brier

Avatar for Insulation Northwest
Insulation Northwest
4.8(
107
)
Blown-In Insulation - Install or UpgradeInjection Insulation - InstallInsulation - Install or Upgrade

Serving Brier, WA and surrounding areas

Approved

Super Service Award Winner

In business since 2006

Free estimates

Warranties offered

"Insulation NW did an excellent job of removing old inadequate insulation from an attic and crawlspace and replacing it with new insulation and wrapping the ductwork. They had two crews, one for the attic and one for the crawlspace, working for many hours to complete the job. A vapor barrier was also installed in the crawlspace. We paid a very reasonable price after the large PSE Rebate was applied."
Additional Photos
Additional Photos
Additional Photos
19 neighbors recently requested a quote
Recommended by74%of homeowners
Avatar for PNW Insulation, LLC
PNW Insulation, LLC
4.7(
255
)
Blown-In Insulation - Install or Upgrade

Serving Brier, WA and surrounding areas

Approved

In business since 2015

Free estimates

Warranties offered

"PNW Insulation completed many insulation tasks on a house for me including wall insulation, crawl space and attic. They were very accommodating with scheduling the work at various times as each area was ready. I highly recommend them."
Before
All insulated
Final with Wmp
Getting ready to start
Inside office

+22

Response time1 day
Response rate93%
43 neighbors recently requested a quote
Avatar for Lake Atitlan Insulation, LLC
Lake Atitlan Insulation, LLC
5.0(
20
)
Blown-In Insulation - Install or Upgrade

Serving Brier, WA and surrounding areas

Approved

In business since 2021

Free estimates

Credit card accepted

"We had Lake Atitlan Insulation remove our old insulation and replace it with R-38. I enjoyed working with Nanni from the initial meeting to the final step of installing the insulation. Very knowledgeable lady and truly exceptional customer service. A highly recommended insulation contractor."
7 neighbors recently requested a quote
Recommended by5%of homeowners
Madrona Home Services, LLC
4.7(
74
)
Blown-In Insulation - Install or Upgrade

Serving Brier, WA and surrounding areas

Approved

In business since 2010

Free estimates

Customers say: Quick response

"We had a wonderful attic insulation experience with Madrona Home Services! They had the best pricing, including the Puget Sound Energy discount and they managed all the paperwork. We were able to schedule two weeks after the quote, and their team worked fast and efficiently on installation day. They removed old saw dust insulation and laid down batting, as well as going above and beyond by creating an 8x8 storage platform. Our house feels noticably cozier with consistent temperatures. 10/10"
Response time1 day
6 neighbors recently requested a quote
Recommended by100%of homeowners
Avatar for Madrona Insulation
Madrona Insulation
4.9(
68
)
Blown-In Insulation - Install or UpgradeInjection Insulation - InstallInsulation - Install or Upgrade

Serving Brier, WA and surrounding areas

Approved

In business since 2009

Free estimates

Warranties offered

"Fantastic. Of all the home improvement companies who have worked on many different jobs at this house in six years, Madrona takes the cake for providing the best quality work and amazing customer service. Madrona was the only company who gave us a thorough plan to not only put insulation in the attic but also to improve ventilation and ensure all roof penetrations were properly sealed. They added 1300 ft of R-44 blown fiberglass insulation over existing rock wool insulation that was fine but inadequate, to bring it to R-49. They fashioned a new wood access panel to the attic with a huge covered batt of fiberglass insulation fastened on the upper side and it feels like opening a secure air lock on the rare occasions where we've looked up into the attic. After they sealed all air penetrations in the attic they were very happy to show us what they did before adding the insulation. They installed insulation shield around the chimney, six roof jacks for proper venting, and vented kitchen and bath fans to dampered roof jacks, insulated with R-11 fiberglass batts. Four years later, the attic looks fantastic - there is no sign of any moisture and the blown in insulation looks as fluffy and lofty as when it was newly installed. I mistakenly thought one of the bath vents had been filled with insulation foam, causing the fan to not work very well, and Madrona sent someone out the next day even though the job was completed four years ago. Curt investigated and then politely and patiently explained that the side vent had been replaced with a better roof vent. And indeed, the fan was blowing air through the roof vent they installed and it is the old fan that is the problem, not Madrona's work. It would be wonderful if all companies stood behind their work this way."
.
.
5 neighbors recently requested a quote
Recommended by96%of homeowners
Avatar for Insulation Pro Inc.
Insulation Pro Inc.
5.0(
19
)
Blown-In Insulation - Install or UpgradeInjection Insulation - Install

Serving Brier, WA and surrounding areas

Approved

Super Service Award Winner

In business since 2025

Free estimates

Warranties offered

"We literally been roasted in our house especially on the second floor with that late heatwave going on . Eric from Insulation Pro took care of our attic. Full insulation replacement. Some mold problems and vents to reconnect . I was skeptic I even tested with the thermostat furnace but it literally did the job. Couldn't be happier."
Attic project
During job progress
During process
Crawl space full service
Before project crawl space

+59

Response time5 hrs
Response rate95%
6 neighbors recently requested a quote
Avatar for Acorns Attics & Crawls, LLC
Acorns Attics & Crawls, LLC
5.0(
17
)
Blown-In Insulation - Install or Upgrade

Serving Brier, WA and surrounding areas

Approved

Super Service Award Winner

In business since 2024

Free estimates

Credit card accepted

"Acorns Attic was hired for a rodent removal job and I had some insulation replaced since it was dirtied with rodent droppings. Phil and team did a great job. They took plenty of pictures of before and after. I haven’t had rodents since they patched up the openings and the insulation looks great!"
Response time4 hrs
Response rate100%
30 neighbors recently requested a quote
...
Showing 1-10 of 105
Drywall Insulation questions, answered by experts

Textured walls can increase the value of your home if the style is modern and seen as a desirable feature and not something a prospective buyer would need to remedy. A good example of this is popcorn texture versus Venetian plaster. The plaster wall would add value to your home, whereas the popcorn texture may be something a new buyer would want to remove.

You should do a little bit of sanding between adding coats of mud. Knock down any ridges or significantly imperfect areas through sanding, which should help you apply the next coat of mud smoothly. If your first coat of mud is pretty smooth after it dries, a quick sanding is all you’ll need. Don’t forget to wipe away any dust after each sanding process.

Although they are used for similar tasks, spackle and joint compound are not the same. Joint compound, also known as drywall mud, consists of limestone and gypsum and is primarily used for large-scale projects like taping and finishing seams on new drywall. Spackle is composed of gypsum and binding agents, making it a thicker compound best suited for small wall repairs like filling nail holes or cracks, as it dries quickly and is easy to sand. For small repairs, either product can be suitable. However, you can use joint compound for small jobs in place of spackle, but you cannot use spackle for large-scale taping and mudding projects.

The best tool for cutting a hole in drywall is a drywall saw. Its serrated blade and ergonomic design make it efficient for both straight cuts and more intricate shapes, ensuring clean and precise results in various drywall cutting applications.

It’s highly recommended to use studs for a TV mount. The last thing you want is to be watching your favorite show when the TV falls off the wall. Studs are much stronger than drywall and quite a bit stronger than drywall anchors but, if you can’t find the studs or there simply aren’t any where you need them, you can use drywall anchors. It’s extremely important to make sure the anchors are rated for the load of the TV. We recommend using anchors that are rated far beyond the weight of whatever you’re hanging. Our suggestion is metal drywall toggle anchors. 

The Brier, WA homeowners’ guide to drywall insulation services

From average costs to expert advice, get all the answers you need to get your job done.