Top-rated toilet pros.

Get matched with top toilet pros in Halls Crossing, UT

Enter your zip and get matched with up to 5 pros

Need a pro for your toilet service project in Halls Crossing, UT?

Select your specific project to find the pro for you.

Find Toilet pros in Halls Crossing

Replumb Specialties Inc.
3.9(
9
)
Faucets, Fixtures and Pipes - Repair or ReplaceFaucets, Fixtures and Pipes - Repair or Replace - For Business

Serving Halls Crossing, UT and surrounding areas

In business since 1992

Free estimates

Warranties offered

"RSI is a great replumb company. The actual replumbing was outstanding and we opted for the upgraded pro-plex fittings to increase our warranty from 10 to 25 years (not an up sell by Jamey - our choice). They also put in-place a dedicated recirculation line for our tankless water heater. The RSI team (Kenny and Milo) was expert at locating and replacing the old polybutylene piping with minimal impact to sheetrock, tiles, and fittings. They finished the work early but were delayed in finalizing the project due to a delay from the Regional Building Inspectors, not RSI's fault. Our only suggestions are 1) better daily clean-up, 2) better attention to detail repainting sheetrock (we had to repeatedly point out areas for a 'redo' and adjacent areas for touch-up) - this seemed harder to do that we expected (this is why we gave them a B rather than an A for quality). Jamey was very responsive to us and answered our questions/concerns thoroughly and promptly. We will recommend RSI our neighbors and friends.
"
Recommended by85%of homeowners
One Call Services
New to Angi
Drain Clog or Blockage - Clear

Serving Halls Crossing, UT and surrounding areas

In business since 2016

Free estimates

Credit card accepted

we take great pride in our experience, expertise, quality and customer service that we provide to meet the consumers needs. It is our mission to provide excellent workmanship and complete customer satisfaction from start to completion of a project. In order to understand the needs and expectations of our customers, we take great care to work and communicate with every customer in a professional manner. Our reputation is based on service, safety and quality, regardless of how large or small the job.

Toilets questions, answered by experts

Basement toilets don’t always need a pump. However, it is the most common setup because plumbing systems use gravity to move waste away from the home. Basement toilets often sit below the home’s main sewage system, and installing a sewage ejector pump pushes the wastewater and sewage up to the main sewer line. Alternatively, you can use an upflush or macerator toilet that breaks down the waste and pushes it straight to the main sewer line rather than via a sewer line from the bathroom.

A running toilet is not a plumbing emergency, but you will want to try some DIY fixes or call in a plumber to prevent wasting gallons of water. The three most common causes of a running toilet are a broken or dirty flapper, an incorrectly sized chain between the flush lever and flapper, or a float that is out of position.

Yes, pressure-assist toilets leak, but less often than regular toilets. You might experience leaks from your toilet due to worn-out parts, water pressure in your plumbing that’s too high or low, poor installation, or cracks in your tank. These toilets are harder to fix on your own than gravity-fed ones, so it’s best to call a plumber if you can’t figure out what’s wrong, 

Some older homes have toilets in the basement to combat sewage backups. This type of toilet, also known as a Pittsburgh potty, acted as a safety valve over the incoming sewer line. If a line backed up, it would back up into the toilet because it was the lowest fixture in the home, keeping it out of sight and away from the finished areas of the house.

Basement toilets were also used by workers with messy jobs, like those who worked in coal mines or steel mills. This way, they could clean up and avoid tracking dirt through their home.

If you’ve accessed the bolts and nuts that hold your toilet seat in place and can’t unscrew them, it’s possible that they were overtightened or that the material corroded over time, making it impossible to unscrew. If that’s the case, you can either call in a plumber for help, or you can DIY a solution if you’re careful. Lay down masking tape around the mounting bracket and then use the tape as a surface to lay a hack saw blade. Move slowly to cut through the bracket and bolt, being careful not to damage the porcelain in the process.

The Halls Crossing, UT homeowners’ guide to toilet services

From average costs to expert advice, get all the answers you need to get your job done.