Top-rated drywall pros.

Get matched with top drywall pros in La Grange, TX

Enter your zip and get matched with up to 5 pros

Need a pro for your drywall service project in La Grange, TX?

Select your specific project to find the pro for you.

Find Drywall pros in La Grange

Avatar for Zuniga Drywall
Zuniga Drywall
5.0(
2
)
Drywall - InstallDrywall - Repair

Serving La Grange, TX and surrounding areas

Approved

In business since 2018

Free estimates

Emergency services offered

Zuniga Drywall is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Response time2 hrs
Response rate95%
Recommended by100%of homeowners
BluSky NM Drywall Lath & Plaster Inc
4.8(
249
)
Drywall - InstallDrywall - Install - For BusinessDrywall - Repair+1 more

Serving La Grange, TX and surrounding areas

In business since 1994

Free estimates

Emergency services offered

"The crew showed up every morning on time. They patched/drywalled and textured numerous small areas. The texturing was so good, that it is almost impossible to detect where the repairs where made. They also framed, drywalled and textured the kitchen area for recessed lighting installation. They repaired an area where there was a shower leak. They replaced the drywall and textured an area where a closet had been removed. On every part of the project, they exhibited superior workmanship. And at the end of every day, they cleaned up after themselves. Hire them again? Definitely yes! 
"
Additional Photos
Additional Photos
Additional Photos
Recommended by98%of homeowners
Avatar for JC Drywall
JC Drywall
4.7(
12
)
Drywall - InstallDrywall - RepairDrywall - Repair - For Business

Serving La Grange, TX and surrounding areas

In business since 2010

Free estimates

Small jobs welcome

"Josue was great to work with. Heâ s honest, hard-working, and willing to do what it takes to get the job done right. I highly recommend him for your next job. My drywall and paint project is complete and looks great!"
Response time10 hrs
Response rate88%
Recommended by88%of homeowners
Avatar for Omar Drywall Repair
Omar Drywall Repair
5.0(
7
)
Drywall - InstallDrywall - Repair

Serving La Grange, TX and surrounding areas

In business since 2025

Free estimates

Emergency services offered

"Omar reached out to me and set a good price for the work to be done. He confirmed the appointment and was very prompt. He did the drywall repair in about an hour and took very good care of my home. The work was professional and top notch."
Response time40 mins
Response rate100%
...
Showing 1-10 of 80
Drywall questions, answered by experts

The two most common drywall thicknesses for ceilings are 1/2-inch and 5/8-inch. For most standard residential applications, 1/2-inch drywall is sufficient and widely used. It provides adequate support and is lighter and easier to handle during installation compared to thicker sheets. However, 5/8-inch drywall is often used for specific cases where additional benefits are needed. It is heavier but provides superior sound dampening and fire resistance. You should consider using 5/8-inch drywall for ceilings in commercial buildings, between a garage and a living space, or above a finished basement to meet building codes or for enhanced soundproofing.

You can usually tell if you have plaster or drywall by touch (plaster is harder, colder, and smoother than drywall) or by tapping on it (drywall sounds hollow, plaster does not). If you still cannot tell, peek under an outlet cover and check the cut edges. The rough edges show the composition of the wall. You will see either drywall (two paper sheets sandwiching gypsum material) or only plaster material (no paper sheets).

There are six levels of drywall finish, from 0 to 5, that refer to the amount of work performed during the finishing process.

Level 0: Drywall is hung with no finishing work.

Level 1: Tape is placed over the seams between drywall sheets.

Level 2: A thin layer of mud is applied over the tape and screw holes. This level is common for utility rooms or walls that will be covered.

Level 3: A full coat of mud covers the screw holes and tape, but the surface is not sanded. This is often used in garages.

Level 4: This is the most common finish for visible interior walls. It involves applying two coats of mud over seams and screw holes, with sanding between each coat, creating a smooth surface ready for flat paint.

Level 5: This is a high-end finish for luxury homes. It includes full taping, mudding, and sanding, plus a final skim coat over the entire surface before painting.

There is no way to cut drywall without making dust, but you can reduce the amount of dust and especially the dangerous airborne particles by using manual cutting tools. Using a utility knife to score and snap your drywall will minimize dust production, and a jab saw for cutting cutouts for boxes and fixtures will generate almost no airborne dust. Even if you use these methods, you should still wear a respirator and safety goggles to avoid damage to your lungs and eyes.

There are a few ways to figure out if your walls are plaster or drywall, but the pushpin method is probably the easiest option. To try it, choose a part of your wall where you can insert a pushpin or thumbtack without leaving an obvious mark. If it goes in easily, you have drywall. But if the wall is tough to penetrate, that’s plaster.

The La Grange, TX homeowners’ guide to drywall services

From average costs to expert advice, get all the answers you need to get your job done.