Top-rated contractors.

Best contractors near Blackville, SC

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Blackville, SC?

Select your specific project to find the pro for you.

Top-Rated Contractors in Blackville - Updated Nov 2026

John Marshall Sturgess Builder
4.4(
5
)
Major Home Repairs (General Contractor)

Serving Blackville, SC and surrounding areas

Approved

In business since 2010

Free estimates

Emergency services offered

"This was my first experience hiring a contractor and Mr. Sturgess's was great to work with. He was able to meet with me outside of my work hours to go over my plans. His crew was on time, friendly, and answered any questions I had. Mr. Sturgess rates were very reasonable, and he and his team are very honest and easy to work. Since they have finished converting my carport to the screened sun room, I asked if they could go ahead and finish some other projects for me. I can't wait until all of my projects are done."
Response time4 days
Response rate100%
5 neighbors recently requested a quote
Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Blackville, SC and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Blackville, SC and surrounding areas

In business since 2006

Credit card accepted

"Purchased coupon on August 11, 2011.  Because I was remodeling my kitchen myself after work and weekends, I didn't have time to deal with the creating the room drafts, plans, layouts or measurements she required.  I did contact Jill and explain the situation and she was very understanding.  She said because I contacted her, not to worry about the deadline.  I remained in contact with her over the next few years (that's how long it took me) and when I was ready around the start of 2014, she worked hard to provide her new design.
A true professional and great person to work with.  The design was spot on and my wife and i were very impressed.  Thank you Jill.
"
Recommended by55%of homeowners
Showing 1-10 of 33
Unfinished Carpentry FAQs, answered by experts

Bow windows need support because they are large and extend out from the exterior wall of the home. Bow windows may extend 1 foot to several feet from the outside of the home, so you’ll need to provide additional support to handle this weight. A window contractor will be able to provide the proper amount of support for your new bow window.

Most load-bearing walls are exterior, though they can also be interior.

One of the most common house framing basics for decades has been using wood for the framing work. However, some framing contractors now suggest using steel frames. Steel is lightweight, resistant to fire, and resistant to moisture, all of which are areas where wood framing could cause problems. However, steel framing is more expensive than wood and limits your ability to insulate the home.

Bump-out additions can extend anywhere from 2 to 15 feet from an existing room. The right size will depend on how you plan to use the new space. For a cantilever bump-out, which doesn't require additional foundation support, the limit is typically 24 inches (2 feet). If a footing and foundation are part of the project, a bump-out can be much larger, even encompassing a whole room. It's also important to remember that many residential properties have limits on the total house size relative to the lot size.

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

The Blackville, SC homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.