Top-rated sandblasting pros.

Get matched with top sandblasting pros in Madras, OR

Enter your zip and get matched with up to 5 pros

Need a pro for your sandblasting service project in Madras, OR?

Select your specific project to find the pro for you.

Find Sandblasting pros in Madras

Avatar for Optimum Painting & General Contracting Inc
Optimum Painting & General Contracting Inc
4.9(
52
)
Exterior Surfaces - SandblastingExterior Surfaces - Sandblasting - For Business

Serving Madras, OR and surrounding areas

In business since 1993

"We took 7 bids from Sisters/Redmond/Bend area paint contractors. We chose Optimum Painting for three reasons: First, Angie's List rates them highly, over a number of years. Second, John Chabot (president and bidder) is low-key, reponsive and informative. John suggested a longer-lasting paint, for a modest extra cost). Third, Optimum's bid was very competitive. Bo did a great job of prepping, painting and cleaning up. Throughout, customer service was utmost. We're relieved to have the house repainted in a timely manner, before winter sets in. Yes, we recommend John's team at Optimum Painting, without hesitation."
Front Door
Garage
Finished
This is an old antique solid door.
This is the door after being stripped.

+5

Recommended by97%of homeowners
Avatar for Integrity Jack Of All Trades
Integrity Jack Of All Trades
5.0(
2
)
Exterior Surfaces - SandblastingExterior Surfaces - Sandblasting - For Business

Serving Madras, OR and surrounding areas

In business since 2022

Free estimates

Credit card accepted

As a Jack of All Trades Professional; there are a variety of tasks that I am able to tackle but here is a list of the most common jobs I do; epoxy flake flooring or coating (normally in the garage), concrete overlay coating or new concrete floor coating interior, natural gas hook-ups to firepits, driveway (concrete/asphalt) crack repair & reseal, flooring/driveway resurface or coating, door installation, amongst many others.

Close up Epoxy Flake Garage Floor
Epoxy Flake Floor
Epoxy Flake Finish
Broadcasted Epoxy Flake
Broadcast Epoxy Flake

+15

Recommended by50%of homeowners
Avatar for JBC Group Solutions Inc
JBC Group Solutions Inc
4.0(
4
)
Exterior Surfaces - SandblastingExterior Surfaces - Sandblasting - For Business

Serving Madras, OR and surrounding areas

In business since 2007

Emergency services offered

"They did a real good job. They were real professional. We can now open the garage door from the inside of the house and now it is so smooth that we have to check to see if we hit the button to open it or close it.  Before we used to know when it was opening or closing because it used to make a noise. It helps when you move to a city where you are new. "
Custom Staircases
Custom Exterior Restoration
Custom Bathrooms
Recommended by75%of homeowners
Sandblasting Services questions, answered by experts

The cost of sandblasting depends on the scope of the project, the surface type, labor, and equipment required. Services typically cost between $50 and $80 per hour, though most professionals charge by surface area at a rate of $1.50 to $7 per square foot. Total project costs can range from $700 to $12,500, with an average homeowner spending around $3,200 to sandblast a 1,000-square-foot surface.

Sandblasting is useful when you need to strip material off a hard surface. Common reasons to sandblast are to remove paint, rust, or get a surface ready for a new material. You aren’t limited to surfaces like walls either—you can sandblast rusted tools, bicycle frames, cement, bricks, and many others. If what you’re sandblasting is still structurally sound, sandblasting can be a fast and inexpensive way to revive the original material. 

Sandblasting removes old paint, rust, and grime efficiently, providing a clean surface for refinishing.

You can concrete can be done when it’s wet or dry. However, it’s safer when wet, as harmful dust and chemicals are present. Sanding it when dry is faster, but you’ll agitate more dust and chemicals, meaning you’ll need to be more careful.

The best way to sand a deck is by cleaning it, sanding the boards and stairs with 60- or 80-grit sandpaper, and sanding the railings and posts with 80-grit sandpaper. You should sand in the direction of the wood grain to avoid damaging the timber. When sanding your deck, use medium pressure and aim for an even sand. Pressing too hard with a sander can damage decks, as most are softwoods.

The Madras, OR homeowners’ guide to sandblasting services

From average costs to expert advice, get all the answers you need to get your job done.