Get matched with top glass block pros in Shreve, OH

"Scott was great to deal with and their workers did a nice job."

"Tim originally came out looked over the job and wrote up an estimate. Came back a week later and completed the window install and had a new screen in the Door Wall. His pricing was lower than any other estimate. He also showed me the Glass Block window that he was installing. I would hire him again if I ever need Glass Block Windows again."

"This company is a joke. Steve is a snake oil salesman who pressured us into a $10k job. He came out and misdiagnosed the problem resulting in him switch the plans several times. When it came time to get the work done, my brother and I had to finish the job. If your job is to take water from the foundation how is exterior work not included in the quote. Furthermore, Steve has ZERO man management and LIMITED knowledge of his field. His crews have no idea what they're doing, and his front office is a joke. I had to explain to them that they do indeed make male pipe fittings despite Steve and his associates persistence that they don't. If it's a choice of having water in your house or working with these jokers l'd recommend just letting the house fill with water. Pathetic, unprofessional, and a waste of time and money. SMD Stevie."

"Jacob is the best in the business. It’s very comforting to know I have a reliable contact for whenever I’m having any basement/water issues or any questions. He also has a lot of references for other projects. 10/10 recommend. Thanks again Jacob!"

"These are facts: The problem: Hired to move water from walls and floor to a sub pump to be pushed out side per their recommendation because of a leaky Basement. The fact:, upon completion, one plastic pipe, connected with a ferncoe was leaking after their work was complete and they left the job They came back to fix it and did,but said everything was fine..this from their "managing - inspector". We questioned many things to all questions the answer was it is correct. So we hired an inspector because it was leaking from the wall where they attached the sub pump pipe; and the pump is working regardless if its even wet outside. Now from an inspector: INTERFERENCE- Upon inspection and removing the lid, the pump float was restricted. Once the pump was moved it activated and the primary pump continued running even after the water was gone. This was due to the small amount of room in the well causing the pump float to hit the sidewall and not drop down according with the lowered water level. The Inspector moved the pump unit over, however the orientation of the float needs to be corrected (turned) so it is away from the lipped sidewall to prevent reoccurrence, 2. PUMP AND WIRES INTERFERENCE- The secondary pump is piped with same diameter piping but the movement between the pumps/piping can also restrict the float fall zone if pump is not orientated with float away from pit sidewall. The pump wires should be zip tied to the pipe as they also fell into the area of the float and could also prevent float on/ off operation. This pit is small for the size pumps used so orientation and interference of wiring needs to be correct to prevent failure of activation or deactivation. 3. Both pumps should have a check valve be installed in line to prevent pump cycling that could prematurely burn out pump motor. Install two 1.5” check valves in the piping. 4. PIPING LEAK - The piping was leaking out of the cinder block wall at the point of drain penetration. The piping was moving at the interior, but fixed (non movable) at the exterior. This means that the pipe is either cracked or was not glued somewhere within the wall cavity. Break out the cement around the pipe and re-pipe and reglue as required. 5. COVER/LID INTERFERENCE- When trying to install this chopped/cut up cover it causes the pumps (due to piping interference) to move around which recreates the issue in #1 by moving the pump float against the wall. A new lid and proper orientation (away from the sidewalls) needs to be completed. A better piping configuration for this pit due to its size would be to use a inverted wye as shown here, thereby eliminating pumps being pushed together when installing the lid. 6. HOLE MISSING- A 1/8” hole needs to be drilled in the secondary pump line to reduce pressure and prevent pump from becoming air bound and eventually seizing. They canceled last week because of a team sickness and also agian this week. So the weeks pass by, no one comes and they have asked now to reschedule a third time.I asked to be copied on the E-mail asking for a manger to call me to talk about this issue. I was told the owner is on vacation and that the only person I can speak to is sick. So I guess as the water keeps leaking, and the pump keeps running, they consider it not urgent enough t0 handle this situation. In my experience, any owner worth anything woudl want to knw about such a travesty in service, but according to the company. the owner is on vacation and not to be disturbed and anyone that could help will get back to us within 48 hours."