Top-rated toilet pros.

Get matched with top toilet pros in Crouse, NC

Enter your zip and get matched with up to 5 pros

Need a pro for your toilet service project in Crouse, NC?

Select your specific project to find the pro for you.

TRUSTED BY CROUSE, NC HOMEOWNERS

  • Average homeowner rating star icon4.6
    Average homeowner rating
  • Verified reviews icon748
    Verified toilet services reviews

Find Toilet pros in Crouse

Avatar for Pro Service Septic & Plumbing
Pro Service Septic & Plumbing
New to Angi
Drain Clog or Blockage - ClearFaucets, Fixtures and Pipes - Repair or ReplaceFaucets, Fixtures and Pipes - Repair or Replace - For Business

Serving Crouse, NC and surrounding areas

Approved

In business since 1989

Free estimates

Offers commercial services

We invite you to experience a tradition of customer satisfaction that will exceed your greatest expectations. Our professionalism and quality workmanship will accurately reflect your taste and lifestyle. From conception to completion, we work with you until the job is done. We are ethical, honest, and easy to communicate with. \n\nCall us today you'll be pleased you did. Thank you!\n

Sewer Man Clean
...
Showing 1-10 of 150
Toilets questions, answered by experts

The average cost to hire a plumber is typically between $45 and $200 per hour, with a common average rate around $125 per hour. This cost can vary based on your location, the plumber's experience, and the complexity of the job. Rates are often broken down by experience level: an apprentice may charge $45 to $90 an hour, a journeyman $60 to $110 an hour, and a master plumber $80 to $200 an hour. While hourly rates are standard, some plumbers may charge a flat fee for routine projects or offer project-based pricing. It's also common for plumbers to charge a minimum service or trip fee. For reference, some typical flat-rate costs for common jobs include: drain unclogging ($220), leaky faucet repair ($270), burst pipe repair ($400), toilet repair ($300), and water heater repair ($600). Note that these rates are for standard service hours; emergency, holiday, and after-hours calls will cost significantly more.

Yes, you can pour water down the toilet to help it flush. For each flush, you’ll need 1 to 2 gallons of water for newer toilets or 3 to 5 gallons of water for older toilets. Rather than dumping the entire bucket in all at once, pour the water in slowly for the best results. If you’re pouring water down the toilet to help it flush after a clog, only use 1 gallon of hot water.

Yes, pressure-assist toilets leak, but less often than regular toilets. You might experience leaks from your toilet due to worn-out parts, water pressure in your plumbing that’s too high or low, poor installation, or cracks in your tank. These toilets are harder to fix on your own than gravity-fed ones, so it’s best to call a plumber if you can’t figure out what’s wrong, 

Start by gutting the old fixtures and features that need to be removed, such as the tile, vanity, and flooring. You may benefit by removing the toilet, even if you intend to use the same one. Next, install the new shower or tub, followed by the flooring, and then the drywall, which you should then paint. After that, install your new cabinets, vanity, countertop, sink, and faucet, in that order. Replace your light fixture next. Lastly, reconnect the toilet.

Yes, you can install a basement bathroom without breaking concrete by using an upflush toilet system, which includes a macerator pump. These systems sit on top of the concrete floor, so you don't have to drill into it to install plumbing. The macerator pump breaks up waste until it is soft enough to pass through a discharge pipe to the main sewage line. This method saves you time and money by bypassing the need to break concrete to connect drain pipes.

The Crouse, NC homeowners’ guide to toilet services

From average costs to expert advice, get all the answers you need to get your job done.