Top-rated roofers.

Best roofers near Meadville, MS

Enter your zip and get matched with up to 5 pros

Need a pro for your roofing project in Meadville, MS?

Select your specific project to find the pro for you.

Top-Rated Roofers in Meadville - Updated Nov 2026

Complete Finish Cleaning Co
New to Angi
Roof - Clean

Serving Meadville, MS and surrounding areas

Approved

We specialize in post-construction cleaning, helping transform dusty, messy job sites into clean, polished spaces that are ready for their next chapter.\n\n🏠 New construction\n🏗️ Remodels & renovations\n🧹 Post-construction cleanup\n✨ Final cleans & move-in ready services\n\nWe’re committed to reliable service, attention to detail, and leaving every project looking its best.\n\nYou build it. We make it shine. ✨

Avatar for Weather Guard Lifetime Metal Roofing
Weather Guard Lifetime Metal Roofing
4.4(
40
)
Asphalt Shingle Roofing - Install or ReplaceAsphalt Shingle Roofing - Install or Replace - For BusinessAsphalt Shingle Roofing - Repair+26 more

Serving Meadville, MS and surrounding areas

In business since 1989

Free estimates

Credit card accepted

"Over all it was OK.  I was not happy with how much time I had to spend picking up trash after they left - from strips of sharp metal, to dozens of screws every day for a week (literally), to their snack wrappers and drink cans every evening.  The house had been painted a few months prior to the roof job and they managed to gouge several pieces of newly painted wood from the sides of the house.  I was told it would not mildew and 2 years later it has and needs a cleaning.  Had they been honest about that, I would have gone with a darker color.
"
Our Showroom
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by86%of homeowners
Avatar for ADT Solar
ADT Solar
4.4(
111
)
Asphalt Shingle Roofing - Install or ReplaceAsphalt Shingle Roofing - Install or Replace - For BusinessAsphalt Shingle Roofing - Repair+26 more

Serving Meadville, MS and surrounding areas

In business since 2008

Free estimates

Warranties offered

"Rep. checked entire system. He found several wires not connected properly and fixed this. He also made recommendations regarding the attachment of the panels to the rood that would provide more stability and leakproofing. The representative appeared to know what he was doing - much better than others, including the representative who was engaged by the roofer (who replaced our rood due to hail damage) to disconnect/connect the panels."
11 kW PV Installation
5 kW PV Installation
9.5 kW PV Installation
Recommended by89%of homeowners
...
Showing 1-10 of 86
Roofing FAQs, answered by experts

Installing a green roof costs between $10 and $30 per square foot. Green roofs cost slightly more than standard roofs, due to the extra materials and installation know-how required. The type of green roof you choose also impacts the cost, with intensive roofing systems costing considerably more than extensive roofs.

Yes, a roof blister can cause a leak if it gets to the point where it pops. Prior to popping, a roof blister is just an aesthetic issue, but once it pops, you’re left with a small hole in the shingle. Water from rain and snow can easily get inside this hole and interact with your underlayment, roof decking, and the building material below.

Gable vents are more common in older homes built before the 1970s. Homes built after this era use ridge vents or soffits, but you can sometimes find homes with both gable and ridge vents. Gable vents can have a purely aesthetic purpose, while ridge vents hide in the roof shingles so air can flow under the roof while keeping the attic dry.

A square of shingles covers 100 square feet and usually ranges from 150 to 240 pounds. It all depends on the material and type of shingle.

The proper specifications for furring strips can vary, so you should always consult the roofing manufacturer's guidelines or your roofer. However, general recommendations are as follows:

  • Thickness: Furring strips are typically 1 to 1-1/2 inches thick, meaning standard 1-by or 2-by lumber works well. In areas with extreme winds, a thinner strip may be preferred to limit how much air can get under the roof and cause uplift. A thicker strip can add slightly more insulation but will also increase installation costs.

  • Spacing: The recommended spacing for furring strips is between 12 and 24 inches apart on center. Proper spacing is crucial for ensuring good airflow, adequate drainage, noise reduction, and better energy efficiency. The ideal spacing can depend on the roof's pitch and the specific type of metal roofing being installed.

The Meadville, MS homeowners’ guide to roofing services

From average costs to expert advice, get all the answers you need to get your job done.