Top-rated concrete cutting pros.

Get matched with top concrete cutting pros in Waseca, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Waseca, MN?

Select your specific project to find the pro for you.

Find Concrete cutting pros in Waseca

Avatar for American Waterworks
American Waterworks
4.5(
171
)
Concrete Flatwork - Repair & Resurface

Serving Waseca, MN and surrounding areas

Approved

In business since 1989

Free estimates

Warranties offered

"They did great. The entire surface was level and free from tripping hazards. It is important to have them seal the cracks because there will be water from snow melt and the concrete will move. This will get you the 5 yr warrantee just in case."
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
628 neighbors recently requested a quote
Recommended by91%of homeowners
thompson concrete and masonry
New to Angi
Concrete - Sawing or RemovalConcrete Flatwork - Repair & Resurface

Serving Waseca, MN and surrounding areas

In business since 1995

Thompson Concrete and Masonry has over a decade in the masonry trades. From concrete foundations, to patios and brick work including fireplaces and tuck pointing, we have the tools and the experience to handle any job. \nChoosing the right mason is very important for you home and projects. All of our projects are built to stand the test of time and to be enjoyed by you and your family for the years to come.\nDon't be shortsighted when choosing a company for your concrete and masonry project, call Thompson and have your job done right at very reasonable prices.

Graystone Concrete & Masonry, LLC
New to Angi
Concrete - Sawing or Removal- For Business

Serving Waseca, MN and surrounding areas

In business since 2009

Free estimates

GrayStone Concrete & Masonry, LLC, is your 1st and finest choice in concrete and masonry, all right here in our community. GrayStone Concrete and Masonry, LLC, produces elegant concrete and masonry work. Producing the ultimate in quality craftsmanship, with pride in doing great work, we care for your place and your project, as if it was our own. We are your one-stop shop serving the complete project, even aspects not noticeable -- we allow the whole to be completed right when it should be. Rest assured and everything is good with GrayStone Concrete & Masonry, LLC. We are perfectionists and all of our work is guaranteed. Call now.

Showing 1-10 of 16
Concrete Cutting questions, answered by experts

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Sawing your hot tub into more manageable chunks so it can be lifted easily into a truck takes several hours. Generally, 2.5 hours for smaller hot tubs and around 4 hours for larger ones with the help of one to two people. If money isn't a concern and you want to skip the physical labor, you can hire a pro to get the job done.

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

The Waseca, MN homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.