Top-rated epoxy flooring pros.

Get matched with top epoxy flooring pros in Two Harbors, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your epoxy flooring service project in Two Harbors, MN?

Select your specific project to find the pro for you.

Find Epoxy flooring pros in Two Harbors

Avatar for DBS Residential Solutions, Inc.
DBS Residential Solutions, Inc.
2.6(
18
)
Concrete Finishing, Overlays & Coloring - Apply

Serving Two Harbors, MN and surrounding areas

Approved

In business since 2012

Free estimates

Emergency services offered

"The job needs to be fixed already it wasnâ t done to completion on day one. I needed the concrete patio to shed water away from the house. It currently is shedding water towards the house. Why I hired them is to correct that problem. My hope is this small issue will be able to be resolved today."
Concrete Repair After
Concrete Repair Before
Cabin Stabilization Before
Cabin Stabilization After
Basement Waterproofing After

+8

Response time1 day
Response rate92%
163 neighbors recently requested a quote
Avatar for Mark Betker Construction, LLC -
Mark Betker Construction, LLC -
0.0(
1
)
Concrete Floor Coating-ApplyConcrete Floor Coating-Apply - For Business

Serving Two Harbors, MN and surrounding areas

In business since 2004

Free estimates

Warranties offered

Concrete Coating Solutions specializes in both residential and commercial epoxy flooring, polyurea (polyasparatic), polished concrete, and commercial shop floors including cove, with a proud portfolio of over a decade. We offer the highest quality professionally installed epoxy flooring in the industry today. So, whether you are looking for protective, durable, seamless, stylish, chemical resistant,high MVE resistance, elegant or tough flooring Concrete Coating Solutions is the company to rely on. \nEpoxy Flooring at it��s Finest\n Concrete Coating Solutions, LLC takes pride in using an application of coatings that will not contaminate order-sensitive products. Our products comply with VOC regulations, LA rule 66 and meet USDA approved guidelines.\n

Before
After
Before
After
After

+24

Recommended by100%of homeowners
Epoxy Flooring questions, answered by experts

As with anything you buy, be wary of prices that seem too good to be true. Some low-cost flooring products can contain chemicals that release harmful VOCs (volatile organic compounds) in the form of fumes that can be inhaled or dust that can cause skin conditions.

Even good-quality products can be dangerous for DIY-ers who don’t take proper precautions. Always carefully read manufacturer instructions and wear the recommended protective gear when working with paints and other chemicals. You can also hire a local garage flooring pro with the experience and equipment needed to perform the installation safely with no lingering fumes or debris.

You can whiten concrete for unsealed and unfinished concrete with a solution or either muriatic acid or bleach and water—but never both. However, if your concrete does have a stain, finish, or polish, keep in mind that these hard chemicals could damage the topcoat. Your best bet otherwise is to power wash outdoor concrete slabs or clean indoor ones with a gentle cleaner such as laundry or dish detergent.

Resurfacing a garage floor takes about eight hours on average, with another couple hours over three days to do the epoxy. Epoxy goes on in three coats, with each coat taking 24 hours to dry and cure. You’ll need to keep foot and vehicle traffic off of your garage floor for around 4 days in total when replacing your garage floor, so be sure to plan ahead before you start. This is a great time to organize your garage since you’ll need to move everything out to apply the epoxy.

If your concrete stains are green in color, it indicates the presence of mold or algae—which you should address right away. If left unattended, mold will spread to other areas throughout the home. However, be careful not to disturb mold on indoor concrete surfaces and work with a local mold remediation specialist for specialized care. Once free from mold and algae, seal your concrete to eliminate pores and gaps.

You can seal a concrete slab by cleaning the surface, filling in any cracks, etching the surface, applying a sealer, and letting it dry. Concrete slabs don't typically need sealing, but you can use a topical concrete sealer if you notice signs of water damage. If you haven't already fixed the cause of the leak, then you'll want to repair the plumbing before you seal a concrete slab.

The Two Harbors, MN homeowners’ guide to epoxy flooring services

From average costs to expert advice, get all the answers you need to get your job done.