Get matched with top ceiling fan pros in Becker, MN

"They were on time. Explained what he would do, was very professional and did a great job."

"?"

"After submitting the request to Angi we were contacted by LeBrun Electric to do the work and an initial consultation was scheduled with their electrician. Before that first meeting we called the company and specifically told them that we had problems with previous electricians who did work in our home on a whole home solar system. We also communicated that we would be entering into a lawsuit with them. These facts were also communicated to the electrician, and everything related to previous installations/work was to remain on property due to the pending lawsuit. That was made clear. We communicated this to the electrician several times. There were also comments from the electrician indicating that he knew the past electricians in the house – comments regarding Pat’s health. After completion of the work we found that the meter socket, the breaker, and the breakers were removed from the premises. We were told afterwards that they remove all old material, but it's interesting that the electricians pick and choose what items stayed and what items were taken. All other boxes that were removed from walls, inside and outside, were left behind, but the meter socket and the breaker box containing a lot of very expensive, relatively new breakers were removed. We specifically requested that the meter socket remain on the property because it would play a big role in the lawsuit - it was not code. That meter socket was something that we paid for and was installed in 2020. the breakers in the box were all new and there were at least 3 50-Amp breakers, 7 20-Amp 1 pole Tandem breakers, 1 20-Amp Dual Function breaker, and 9 15-Amp 1 pole Tandem breakers. Less than half of those were returned. The breakers should not have been removed from the house. Now for the safety issues: The state in which the electrical work was left would have guaranteed a failure by the inspector. It was as if the work was deliberately set up to fail. On the Automatic Transfer Switch, the front panel could not be removed because it was jammed into place by the inner panel. This was because the wire in the box was shoved in, too long, not orderly, and therefore pushed out on the 2 panels so they were jammed and could not be removed without a lot of effort. Once the covers were removed, we found that the wires were not secure. The slightest movement caused the cables from the meter to slip loose of the terminals in the ATS. The wires to the multitap connectors were loose as well and many of the strands were bent so the connection was not complete. As I watched the inspector during his inspection, he first checked the breaker box, then followed the lines to the ATS and opened it up. If we hadn’t found the issues first there is no way the inspection would have passed. Also, the electricians put 2 side taps in place on the cables to the meter. Neither of the side taps were tightened and didn’t even connect to the copper of the meter cables. When we turned our solar equipment on to connect to the grid it did not recognize a connection to the grid. This was also something we asked the electrician to do but wasn’t completed. Next is the service disconnect box that we asked the electrician to connect. This is another area where the work done was left unsafe. It was known that we would be opening the box to connect the wires of the system to the service wires once we received the connectors. The wires that were connected by the electrician were loose and slipped from the terminals. Pat was hit by 220 when one of those wires slipped loose. We’re very lucky that he wasn’t injured more seriously. Also, the electricians decided to run the wiring through the bottom of the service disconnect instead of through the top – the cover they placed on the top of the box to seal it did not cover the opening – I can’t believe this would meet code and the service disconnect box needed to be replaced. It was known that we needed the white, red and black 1/0 wire that came into the house to the ‘service disconnect’ to change out/rewire the generator input wire. There was over 45 feet of 1/0 wire that was removed from the house, that was needed for another purpose. The wires should not have been removed from the house and the electrician knew why. Taken from house: Meter socket 45 ft of 1/0 wire (red, black, & white) 7 20-Amp 1 pole Siemens Tandem breakers 9 15-Amp 1 pole Siemens Tandem breakers 1 20-Amp Dual Function breaker 3 50-Amp Siemens breakers New signs were not provided Shoddy labor that would have failed inspection if we had not intervened"

"We were billed $65 for the trip, and then billed $125 for the hour it took the electrician to drive here! He worked very slowly. Took four hours to install a dedicated outlet for our microwave and three new ground-fault interrupters. He worked on existing outlets while those outlets were live! And he refused to use the Wallabot to help locate the wire in the wall, telling us it would only detect live wires -- we knew better but there was no telling him."

"Guys were professional kept the mess to a minimum and cleaned up when job was complete. I really appreciated the care they took of my home and the time they took to get the job done right. I love my solar tubes!"

"Arrived much earlier than I had anticipated, which was OK as they were squeezing me into their schedule to accommodate other non-electrical work being done. Very quick and professional."

"Excellent, they updated a number of outlets and a couple of switches after we did an update on our kitchen. The electrician worked carefully around the new tile work and carefully trimmed one corner to fit the new box. All came out very well and fair priced."