Top-rated woodworkers.

Best woodworkers near Dekalb, IL

Enter your zip and get matched with up to 5 pros

TRUSTED BY DEKALB, IL HOMEOWNERS

  • Average homeowner rating star icon4.5
    Average homeowner rating
  • Verified reviews icon22
    Verified woodworking services reviews

Top-Rated Woodworkers in Dekalb - Updated Nov 2026

Avatar for Drew Pro Carpentry
Drew Pro Carpentry
4.9(
48
)
Interior Trim and Decorative Moldings - Install

Serving Dekalb, IL and surrounding areas

Approved

Super Service Award Winner

In business since 2019

Free estimates

Small jobs welcome

"Andrew and his co worker did an amazing job. They went out of there way to ensure the job was done to our expectations and all the materials required were available to complete the job on time. Andrew is very professional and knows his craft. We have already planned our future project to continue inside door and trim replacement with him. Everything was cleaned up and in place at the completion of the work."
Bifold
Bifold door
Pocket door
Pocket door
Interior doors

+3

Response time1 day
Response rate98%
1 neighbors recently requested a quote
LJ Flooring, Inc.
4.9(
9
)
Interior Trim and Decorative Moldings - Install

Serving Dekalb, IL and surrounding areas

Approved

In business since 2017

Free estimates

Small jobs welcome

"Similar to other reviews Luis went above and beyond to refinish my original hardwood floors. We bought our new house and were searching for someone to do the job. After sending a couple emails, and calling for basic quotes, we went on Angi and immediately after searching for professionals Luis called. He had seen we were searching and told me he would come over the same day to check the floors and give us a quote and that was it. He set up a time to choose our stain, and even grabbed some extra so we could match our Butcher Block counters to our hardwoods. Not only did he start on our floors earlier than expected, he did an amazing job with what looked like an absolute mess before he started. We’re crazy about our floors, and even noticed that before he was finished they had added an extra touch by cleaning our air vents while the grates were off. A true professional and a good person, I would recommend him to anyone. Thank you again!!"
SHOWER REPLACEMENT
SHOWER REPLACEMENT
SHOWER REPLACEMENT
SHOWER REPLACEMENT
SHOWER REPLACEMENT

+32

Response time4 hrs
2 neighbors recently requested a quote
Recommended by77%of homeowners
...
Showing 1-10 of 146
Woodworking FAQs, answered by experts

A contract should outline the scope of work, timelines, costs, payment schedule, and materials used for clarity and protection.

Some states require carpenters to be licensed to perform forms of carpentry, such as framing. The license requires a certain amount of experience and to pass an examination. In states that don’t require carpenters to be licensed, they must be licensed as a contractor if they work independently rather than solely as a subcontractor under a licensed builder. Use Angi’s contractor licensing tool to find out whether a potential carpenter is licensed in your state.

Yes, you can find ceiling joists using simple tools if a stud finder isn't available.

Using a hammer requires patience and a keen ear. Gently tap the ceiling in a grid pattern, listening for sound changes. A hollow sound indicates space between joists, while a solid, dull thud suggests a joist. Mark the location with a pencil and confirm by tapping from different angles.

Alternatively, you can use a nail, but this method will leave small holes. You'll feel increased resistance when the nail hits a joist. Mark the spot and repeat the process every 16 or 24 inches to map the joist locations. This method is considered less reliable than using a stud finder.

Joists do distribute their load to beams, but they don’t sit on top of the beams. Instead, home builders nail or screw the joists directly to the beams such that the end of the joist butts up against the edge of the beam. Beams can sit on other beams for support, but you’ll never see a joist sitting on top of a beam or another joist.

If you don’t have a coping saw, you can use an angle grinder to cope crown molding, but it takes a little more precision. Place your molding down on your workbench, angle the grinder at a 45-degree angle toward the molding, and back cut the wood. You’ll need to carefully angle your grinder to accommodate the curves in the wood, and aim to remove around 1 inch from the profile of the molding.

The Dekalb, IL homeowners’ guide to woodworking services

From average costs to expert advice, get all the answers you need to get your job done.