Top-rated contractors.

Get matched with top contractors in San Luis, CO

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in San Luis, CO?

Select your specific project to find the pro for you.

Find Contractors in San Luis

Avatar for Metro Reconstruction Services, Inc.
Metro Reconstruction Services, Inc.
4.6(
34
)

Serving San Luis, CO and surrounding areas

In business since 1982

Free estimates

Emergency services offered

"Job went well, workers were on time and when necessary worked on weekends. Because of moisture seepage contractor has agreed to return in November at the charge to complete interior plastering which could not be done due to seepage."
Home Inspections
Recommended by94%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)

Serving San Luis, CO and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)

Serving San Luis, CO and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for Jirons Transport & Mobile Welding Repair
Jirons Transport & Mobile Welding Repair
5.0(
1
)

Serving San Luis, CO and surrounding areas

In business since 2020

Free estimates

Emergency services offered

Mobile Welding Services: Gates, Hinges, Stairs, Handrails, Doors, Storage Tanks, Equipment, Farm Maintenance, Equipment Repairs, ETC... (available 24/365. Emergency Welding Repairs. Pipe Fences, Barns, Gates, sheds, carports available as well)\n\nCall us today for a free quote! \n

Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+34

Recommended by100%of homeowners
Showing 1-10 of 18
Unfinished Carpentry questions, answered by experts

Converting a carport into a garage can vary in difficulty depending on its configuration, the condition of the foundation or slab, and its location relative to the house. The process has a lot in common with a home addition, but you can often skip non-essential finishes like fine flooring, trim work, or even drywall and HVAC. The conversion requires experience with drywall, insulation, and other building materials to ensure it’s done safely and correctly. While it might be possible for a DIYer with the proper tools and skills to do the work, it is a complicated and potentially dangerous job. If you’re new to basic construction, it's best to leave this project to the professionals.

When hanging a door frame, it’s recommended that you use screws, not nails. Screws are more secure, easier to tighten, and easier to remove if you need to adjust the frame. On average, the cost to replace a door frame is about $400, but you can save on labor costs if you’re confident in your ability to DIY the project. 

An A-frame home can be cheaper to build than a traditional house, but that is not always a given. Prices can be fairly similar in some cases, depending on the location, design, and necessary site preparation. Costs for an A-frame typically run between $100 to $200 per square foot, which is comparable to the cost of a traditional home. The cost of an A-frame can come in under those numbers if you opt for a prefabricated kit.

A cross brace for a fence gate should stretch from the top corner of the gate’s hinge side to the bottom corner of its latch side at a 45-degree angle to the bottom of the gate. This positioning distributes the bulk of the gate’s weight to the base of the post, taking pressure off the top hinge.

A-frame homes are on the smaller side. While there’s no set square footage amount it has to be, it will usually come in around 1,000 square feet or smaller.

The San Luis, CO homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.