Top-rated welders.

Get matched with top welders in San Marcos, CA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in San Marcos, CA?

Select your specific project to find the pro for you.

Find Welders in San Marcos

Avatar for PJJ Welding & Fabrication, Inc.
PJJ Welding & Fabrication, Inc.
5.0(
33
)

Serving San Marcos, CA and surrounding areas

Approved

In business since 2018

Free estimates

Emergency services offered

"PJJ Welding lengthened the tongue on my trailer to give better backup control. They did a great job and I have them out to construct a horse barn for me. Great people to work with."
Final product
Close up of the oven hood
post insall
sheet steel planter box
completed 3 door enclosure

+23

Response time5 hrs
Response rate91%
13 neighbors recently requested a quote
Avatar for Fusion Welding & Fabrication, Inc.
Fusion Welding & Fabrication, Inc.
5.0(
67
)

Serving San Marcos, CA and surrounding areas

Approved

In business since 2020

Free estimates

Emergency services offered

"If you're looking for Professionalism, high quality, detail oriented work, then Fusion Welding is the company to go to. Not only you get phenomenal work but you also get a great attitude along with it. I highly recommend them."
Aluminum deck
Gate
Interior Railing
Exterior Railing
URM Welding fabrication

+12

6 neighbors recently requested a quote
Recommended by88%of homeowners
Avatar for Palm Steel Inc.
Palm Steel Inc.
5.0(
25
)

Serving San Marcos, CA and surrounding areas

In business since 2020

Free estimates

Small jobs welcome

"Both the owner and his staff are professional in their knowledge of their work as well as the high quality of their product. They are honest, hard working and I would recommend them to anyone looking for a great experience with this company."
Downstairs handrail
Base plate shoe cover
Upstairs rail
Finished Handrail
Left Canopy View

+9

Response time2 days
Response rate87%
Recommended by100%of homeowners
Reynolds Fence CO
5.0(
15
)

Serving San Marcos, CA and surrounding areas

In business since 2000

Free estimates

"We hired Reynolds Fence Co. to remove an old, wood and wire section of fencing and replace it with chain link to match the rest of our fencing. We also had them rework a gate. They arrived on time, kept us informed, and completed the job promptly. We are very happy with the quality of work and would not hesitate to hire them again."
Response time9 hrs
Response rate97%
Recommended by93%of homeowners
Avatar for Bernal Construction
Bernal Construction
4.5(
38
)

Serving San Marcos, CA and surrounding areas

In business since 1999

Free estimates

Emergency services offered

"Raul did a great job for us. He took over a bathroom remodel job that had been started by another contractor. We know contractors don't like to do this, but Raul was willing to take on the challenge! He was excellent at communicating with us throughout the project, and kept to the budget. We would definitely recommend him!"
Kitchen design & Appliances
Kitchen layout
Kitchen detail & countertops
Master Bath
Guest Bath

+11

Recommended by88%of homeowners
...
Showing 1-10 of 55
Welding questions, answered by experts

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

Welding is the process of using extreme heat—and, sometimes, pressure—to attach two pieces of metal. In contrast, metal fabrication is a more involved process that can include welding, sheet metal work, bending, and other forms of metal manipulation. Metal fabrication is a large-scale project that may or may not involve welding, while welding is more often a step in larger fabrication projects.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

The San Marcos, CA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.