Top-rated well and pump technicians.

Get matched with top well and pump technicians in Georgetown, AL

Enter your ZIP and get matched with up to 5 pros

Need a pro for your well and pump service project in Georgetown, AL?

Select your specific project to find the pro for you.

TRUSTED BY GEORGETOWN, AL HOMEOWNERS

  • Average homeowner rating star icon4.4
    Average homeowner rating
  • Verified reviews icon49
    Verified well and pump services reviews

Find Well and pump technicians in Georgetown

WellHose DIY Drop Pipe - You can install your own submersible pump.Free installation classes available. www.WellHose.com




E.J.'s Irrigation LLC

5305 Catalina St.
4.50(
2
)

E.J.'s Irrigation LLC

5305 Catalina St.
4.50(
2
)
Customers say: Quality work
Recommended by 100% of Angi customers
Recommended by 100% of HomeAdvisor customers

Repair work is charged on a hourly rate of $50 - $70 based on varying job conditions. New installations, Redesigns, and System main operating components replacement will require a onsite quote / estimate. 10% Military Discount Payment Options: Cash, Check, Credit/ Debit

Repair work is charged on a hourly rate of $50 - $70 based on varying job conditions. New installations, Redesigns, and System main operating components replacement will require a onsite quote / estimate. 10% Military Discount Payment Options: Cash, Check, Credit/ Debit







HUNTER SERVICES

16364 Hunter Ln
No reviews yet

HUNTER SERVICES

16364 Hunter Ln
No reviews yet
15 years of experience

No cost estimates and inspections, low hourly/task rates, easily customized, no-hassle preventative maintenance provided -- grinder/well pumps and plumbing solutions when you need it......."To Go"! EMERGENCY ON-CALL 24/7-365 (251) 978-3485

No cost estimates and inspections, low hourly/task rates, easily customized, no-hassle preventative maintenance provided -- grinder/well pumps and plumbing solutions when you need it......."To Go"! EMERGENCY ON-CALL 24/7-365 (251) 978-3485

Showing 1-10 of 23
Wells and Pumps questions, answered by experts

The right psi for your well pressure tank depends on the tank’s pressure settings. For instance, if yours is set to 30/50 psi (which is common), the ideal psi is 2 to 3 psi below the cut-on pressure—in other words, 27 to 28 psi. However, if it’s at a higher setting of 40/60 psi, 38 psi would be the appropriate level.

A well pressure tank is located between the well and the well pump, and it stores your water under pressure so that the well pump can eventually do its job. The well pump is activated whenever you turn a faucet on—it pulls the water from the tank into your home. Both are vital parts of a complete well water system.

The average life span of a well pump is between 15 and 25 years, but a few factors can influence how long your well pump lasts. Excessive water demand and cycle frequency are the main causes of premature wear and tear. The well pump’s motor size as well as material and installation quality can also affect its life span.

Excessive pressure (above 80 psi) puts too much stress on plumbing pipes, joints, and fixtures. This can lead to leaks and burst pipes. Plus, it shortens the lifespan of appliances, can waste water, and can raise your utility bills. High water pressure might feel like a gift, but it’s actually a silent threat to plumbing.

A well does not run out of water because the groundwater continues to refill with rainwater that seeps through the ground. If the well is too shallow or there is a drought, a well can run dry or be short in supply. It’s important to have a well deep enough to source enough water for your home’s use. Deeper wells tap into more groundwater reserves. If your well is not producing enough water, you may need to redig your well.

The Georgetown, AL homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.