Top-rated well and pump technicians.

Best well and pump technicians near Stuart, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Stuart, VA?

Select your specific project to find the pro for you.

Top-Rated Well and pump technicians in Stuart - Updated Nov 2026

Avatar for Bud Hypes Plumbing & Sewer Service
Bud Hypes Plumbing & Sewer Service
3.9(
28
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Stuart, VA and surrounding areas

In business since 1981

Emergency services offered

Credit card accepted

"I was very pleased with the service. Evidently the guts who did the estimate were not the same ones who came to do the work. they got the work done and cleaned up well but were aggravated that they were not adequately prepared for the job."
Recommended by75%of homeowners
Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,678
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Stuart, VA and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Stuart, VA and surrounding areas

In business since 1971

Credit card accepted

"Rather than fix the issue the first 2 calls, more refrigerant was pumped into the system. This cost me $75 for each call plus the cost of the refrigerant. The 3rd time, they fixed a valve and refilled the refrigerant and I am monitoring to see if this really fixed the problem. So I am out $225 for service calls fro the same problem and the cost of the refrigerant. I think they take this approach intentionally."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Avatar for Christopher Plumbing
Christopher Plumbing
3.7(
3
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Stuart, VA and surrounding areas

In business since 2000

Emergency services offered

At Christopher plumbing, we are focused on providing exceptional 24 hour services with the highest levels of customer satisfaction & we will do everything we can to meet your expectations. With a variety of offerings to choose from, we're sure you'll be happy working with us. Because we're a small business we don't have the huge overhead expenses that you pay for so we are able to save you money with top of the line technicians. Our excellent reputation and long list of satisfied clients attest to our superior craftsmanship, attention to detail, clear communication, honesty and integrity. We offer discounts for seinors and military.

Recommended by66%of homeowners
Howard plumbing
New to Angi
Well Pump - Install or Replace

Serving Stuart, VA and surrounding areas

In business since 2017

Free estimates

\n \nWe take great pride in our experience, expertise, quality, and customer service that we provide to meet the consumer's needs. It is our mission to provide excellent workmanship and complete customer satisfaction from start to completion of a project. In order to understand the needs and expectations of our customers, we take great care to work and communicate with every customer in a professional manner. Our reputation is based on service, safety, and quality, regardless of how large or small the job.

Wells and Pumps FAQs, answered by experts

Normally, when your well pump turns on or off, you’ll hear a small click. This isn’t anything to worry about, but it can be a problem if it’s clicking continuously. This can indicate that the well pump is short cycling—the pump continuously turns on and off.

This can wear out the motor and provide uneven water flow. If this happens, you may need to get it looked at by a well pump professional to see if you need to repair the switch or pump.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Excessive pressure (above 80 psi) puts too much stress on plumbing pipes, joints, and fixtures. This can lead to leaks and burst pipes. Plus, it shortens the lifespan of appliances, can waste water, and can raise your utility bills. High water pressure might feel like a gift, but it’s actually a silent threat to plumbing.

If you have a small well or a particularly high water demand, it’s possible to overuse your well. How quickly a well replenishes depends on its water source. In this case, you may want to purchase a water storage tank that you can fill from the well in off-hours, or if you’re planning to build a new well and you expect a large water demand, you may want to build a deeper well to match your needs.

Through testing for pH, bacteria, and contaminants, ensuring safe consumption.

The Stuart, VA homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.