Top-rated insulation pros.

Best insulation pros near Kingsland, TX

Enter your zip and get matched with up to 5 pros

Need a pro for your insulation service project in Kingsland, TX?

Select your specific project to find the pro for you.

TRUSTED BY KINGSLAND, TX HOMEOWNERS

  • Average homeowner rating star icon4.5
    Average homeowner rating
  • Verified reviews icon44
    Verified insulation services reviews

Top-Rated Insulation pros in Kingsland - Updated Nov 2026

BluSky NM Drywall Lath & Plaster Inc
4.8(
249
)
Batt, Rolled or Reflective Insulation - Install or UpgradeBlown-In Insulation - Install or UpgradeInjection Insulation - Install+2 more

Serving Kingsland, TX and surrounding areas

In business since 1994

Free estimates

Emergency services offered

"The crew showed up every morning on time. They patched/drywalled and textured numerous small areas. The texturing was so good, that it is almost impossible to detect where the repairs where made. They also framed, drywalled and textured the kitchen area for recessed lighting installation. They repaired an area where there was a shower leak. They replaced the drywall and textured an area where a closet had been removed. On every part of the project, they exhibited superior workmanship. And at the end of every day, they cleaned up after themselves. Hire them again? Definitely yes! 
"
Additional Photos
Additional Photos
Additional Photos
Recommended by98%of homeowners
Avatar for Foam Solutions
Foam Solutions
4.6(
12
)
Injection Insulation - InstallSpray Foam Insulation - Install

Serving Kingsland, TX and surrounding areas

In business since 2017

Free estimates

Offers commercial services

"Joe and the crew were very responsive and also respectful of our time. That came out on a Saturday and finished the job for our 30x30 shop in about 4 hours. Would definitely recommend to anyone for insulation needs. Great price too!"
attic ceiling spray foam
Metal building spray foam
wellhouse
Spray Foam Rig
Gym/Metal Building

+3

Response time1 day
Response rate92%
Recommended by90%of homeowners
Investofoam Insulation
4.0(
4
)
Injection Insulation - InstallSpray Foam Insulation - Install

Serving Kingsland, TX and surrounding areas

In business since 2005

Free estimates

Credit card accepted

"I had previously had another company spray foam my attic, about 3 years ago. It looked ok but I was not seeing much improvement in my electric usage. I had an energy audit done and was told that the spray foam job was very substandard. They did not pull back existing insulation around the soffit and the roof insulation was about an inch in some areas. Investofoam came in and spent an entire day redoing the job. My house has 2 x 8 rafters, they filled them and covered exposed edges. The result was amazing. I am seeing about a 40% drop in energy costs. My attic is never more that 5 degrees warmer or colder that the interior. When a cold front would come through this winter and drop the outside temperature 40 degrees it would take a couple of days for the interior to drop 2 or 3 degrees. I have a 2 stage AC / heatpump with variable air handler, it never has run at high speed, you never hear it at all. Also we never hear thunderstorms unless they are extreme. I highly recommend Investofoam!!"
Response time2 days
Recommended by75%of homeowners
Avatar for AIR NETWORK A/C & HEATING
AIR NETWORK A/C & HEATING
5.0(
10
)
Batt, Rolled or Reflective Insulation - Install or UpgradeBlown-In Insulation - Install or UpgradeInjection Insulation - Install+2 more

Serving Kingsland, TX and surrounding areas

In business since 2003

Free estimates

Emergency services offered

"I received 3 quotes on installing a new 5 ton unit to our house air network was $2,000 cheaper than the # 2 bid and over $3000 cheaper than the other bid. They came when they said and chris was very knowledgeable. We had a new unit installed as well as all new ducting and blown in insulation. I would highly recommend air network in the Weimar area"
Recommended by100%of homeowners
Showing 1-10 of 28
Insulation FAQs, answered by experts

If you’re moving wires, installing new wires, or installing new fixtures in the space you’re insulating, then you will need to hire a licensed electrician to do that portion of the job for you. However, if you just intend on replacing old insulation or adding new insulation over existing insulation, then you don’t need to hire one. Your insulation installer will work around wiring, fixtures, outlets, and switches, even if they’re installing fiberglass batts in the voids where wires run. However, you will need an electrician if you suspect a problem with your wiring during the insulation work.

If you have access to the foundation walls, adding spray foam insulation to your existing unfinished basement or crawl space is straightforward. Replacing existing insulation in your unfinished attic space is possible after removing the old insulation. However, spray foam insulating an existing wall after the drywall is in place isn’t possible unless you remove most of the drywall.

EIFS (Exterior Insulation and Finish System) siding can last from 20 to 60 years, with some properly maintained systems lasting even longer. The exact lifespan depends heavily on several factors, most notably the quality of the initial installation and the consistency of maintenance.

Factors that can shorten the life of EIFS include:

  • Improper or poor-quality installation

  • Moisture intrusion

  • Damage from high winds, storms, or hail

  • Damaged flashing and sealant

  • Lack of regular maintenance and unfixed damage

To maximize the lifespan of your EIFS, it is crucial to hire an experienced and qualified professional for the installation. Additionally, regular maintenance—such as cleaning, repairing small cracks or blisters, and having the system professionally inspected—will help identify and resolve issues quickly, preventing long-term damage.

While there are many different kinds of insulation, spray foam, blown-in, foam board, and batt and roll are the four types you’re most likely to see. That doesn’t mean they’re alike, though. Each one varies drastically in terms of cost, materials used, and how they’re installed—not to mention, how well they limit heat transfer.

The most obvious con of injection foam is the cost. It’s much more expensive to install than fiberglass or spray foam, but it may be your only option (unless you want to remove entire walls around the home). Another con is that it involves drilling into existing material, which has to be repaired after the foam is injected. Some injection foams are made from products that aren’t environmentally friendly, and improper installation can lead to trapped moisture, which can lead to expensive mold remediation down the road. 

The Kingsland, TX homeowners’ guide to insulation services

From average costs to expert advice, get all the answers you need to get your job done.