Top-rated concrete cutting pros.

Best concrete cutting pros near Canton, TX

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Canton, TX?

Select your specific project to find the pro for you.

TRUSTED BY CANTON, TX HOMEOWNERS

  • Average homeowner rating star icon4.5
    Average homeowner rating
  • Verified reviews icon19
    Verified concrete cutting services reviews

Top-Rated Concrete cutting pros in Canton - Updated Nov 2026

Avatar for Texan Concrete
Texan Concrete
New to Angi
Concrete Flatwork - Repair & Resurface

Serving Canton, TX and surrounding areas

Approved

In business since 2019

Free estimates

Credit card accepted

Texan Concrete offers a quality product, with a concrete limited warranty. We will beat any price, top notch satisfaction guaranteed! Family owned and operated, licensed and insured, serving all of East Texas! \n? Residential / Commercial Concrete \n? Driveways, Patios, Sidewalks, etc. \n? Decorative Concrete - Stamp, Stain, and Seal \n? House slabs \n? Parking Lots \n? Epoxy \nTexan Concrete also offers a tree cutting service, along with your concrete

Wrap Around Driveway
Wrap Around Driveway
Covered Patio
Covered Patio
Covered Patio

+28

1 neighbors recently requested a quote
Avatar for KJO’s Construction Services
KJO’s Construction Services
New to Angi
Concrete Flatwork - Repair & Resurface

Serving Canton, TX and surrounding areas

Approved

Free estimates

Emergency services offered

Warranties offered

Send an email to [email protected] or a text to 972-897-8535 about your project to give you a quote & get it done as fast as possible.\n\nKJO’s Construction Services takes pride in waterproofing if you have any water leaks we can take a look & fix it, also we specialize in window wet glazing, painting, roofing, masonry & brick, restoration, carpentry, siding, stucco & texture, etc.

Leak inspection & repair
Leak inspection & repair
Leak inspection & repair
Leak inspection & repair
Leak inspection & repair

+59

...
Showing 1-10 of 96
Concrete Cutting FAQs, answered by experts

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

Yes, but you’ll need reliable steel-cutting tools and safety gear to get started. Shipping containers are typically around ¾ inch thick, so it’s entirely possible to cut through them, but experience and the right equipment are very important. When possible, try to get a container as close to the size you want it as possible.

The Canton, TX homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.