Top-rated well and pump technicians.

Get matched with top well and pump technicians in Texico, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Texico, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Texico, NM

*The Angi rating for Well And Pump Service companies in Texico, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Texico, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on June 16, 2026

Find Well and pump technicians in Texico

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Texico, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

Well pump repair might be covered by your homeowner’s insurance, but it’s typically not. If the damage results from a major storm in your area, flooding, a fire, or some other natural catastrophe, then you should consider filing a claim for the damage. However, if the issue is the result of an aging well pump, your policy will very likely not cover the repair cost. In either case, you should hire a well pump professional inspect your well pump, and then use that information to decide whether or not you should file a claim.

You should have your well inspected once per year. You should also have a well inspection done when you’re buying a house with a private well, when the well cap is opened, when the septic tank is repaired, or when there is flooding.

During your annual visit, a pro will make sure that everything is working correctly and check for certain contaminants, including total coliform. Every other year, they’ll look for things like metals and nitrates, and every five years, they’ll test for pesticides.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

You should check water pressure twice a year to ensure there aren’t any irregularities and that it isn’t too high. It’s also smart to check it any time you notice symptoms of high water pressure (like banging pipes, inconsistent water flow, and leaky fixtures). Similarly, if you live in an area that’s prone to water pressure fluctuations due to municipal supply changes, elevation, or seasonal temperature shifts, check it more frequently. You can buy an affordable water pressure gauge and check the water pressure yourself.

The Texico, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles