Top-rated concrete cutting pros.

Get matched with top concrete cutting pros in Fort Defiance, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Fort Defiance, NM?

Select your specific project to find the pro for you.

Find Concrete cutting pros in Fort Defiance

Avatar for BH Concrete
BH Concrete
5.0(
3
)
Concrete Flatwork - Repair & Resurface

Serving Fort Defiance, NM and surrounding areas

In business since 2014

Free estimates

Emergency services offered

"Good worker maker a verygood concrete on my back yard nice and clean he take all the trash i like i hire again in another proyect to put pour 👍👍👍"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+28

Recommended by100%of homeowners
Request Quote
SMRT Construction Services Inc.
3.3(
88
)
Concrete Flatwork - Repair & Resurface

Serving Fort Defiance, NM and surrounding areas

In business since 1984

Free estimates

Emergency services offered

"After seeing what I needed done, we had to purchase sheetrock, so they followed me to Lowe's so I could buy it, and load it on their truck. They followed me home, and they cut out the bad piece, cut a new piece, and put it up in the ceiling, and screwed, taped and mudded it in.
There were two guys, who worked for about two hours, including the trip to Lowe's. They cleaned up their mess, and the repair was ready to finish and paint in two hours.
"
Recommended by58%of homeowners
Request Quote
Avatar for Dreamstyle Remodeling & Doors featuring Pella
Dreamstyle Remodeling & Doors featuring Pella
New to Angi
Concrete Flatwork - Repair & Resurface

Serving Fort Defiance, NM and surrounding areas

In business since 1989

Free estimates

Credit card accepted

With a strong commitment to customer service, superior product quality, and expert installation, we are proud to have helped more than 67,000 customers in New Mexico, Arizona, California, Colorado, Idaho and West Texas improve their homes. We stand behind our products and installation with one of the strongest lifetime warranties in the home remodeling industry. With easy financing options, we can make your home remodeling dreams a reality for little, or often no, up-front investment.

Additional Photos
Additional Photos
Request Quote
Concrete Cutting questions, answered by experts

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

Welding is the process of using extreme heat—and, sometimes, pressure—to attach two pieces of metal. In contrast, metal fabrication is a more involved process that can include welding, sheet metal work, bending, and other forms of metal manipulation. Metal fabrication is a large-scale project that may or may not involve welding, while welding is more often a step in larger fabrication projects.

The Fort Defiance, NM homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles