Top-rated well and pump technicians.

Get matched with top well and pump technicians in Weldon, NC

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Weldon, NC?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Weldon, NC

*The Angi rating for Well And Pump Service companies in Weldon, NC is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Weldon, NC is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on September 12, 2024

Find Well and pump technicians in Weldon

Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,678
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Weldon, NC and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Called in claim on 6/18; tech assigned on 6 /19; so far so good. Claim was for failed well pump with NO water to my home with two disabled seniors. Due to heavy workload and no extra pay on weekends the tech came for diagnostics 4 days later. He verified the failed pump and tried to purchase one at Home Depot. None in stock, had to be ordered. Pump came in on 6/30 and tech arrived today, 7/1, and expertly installed the new pump. Choice has a $ 500 limit on well repair, which is 1/3 of a typical bill. That dollar cap is riduculous. On a positive note, C-Force provides expert work for Choice and would be my choice for any future work."
Recommended by81%of homeowners
Request Quote
Wildest inc LLC
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Weldon, NC and surrounding areas

Emergency services offered

Warranties offered

Small jobs welcome

Been with my partner for 17 yrs we have done everything from dirt to roof tops on houses hotels motel apartments when I say everything i mean everything you name we can do it ni job to small no job too big free estimates if contract is made no hassle guaranteed professional services, a 100%. We're class A contractors with a great team to get the job done in a timely manner. No need to worry we're here to save the day just one call away.

Request Quote
Wells and Pumps questions, answered by experts

No. Well pump replacement is not recommended as a DIY project, particularly if you have a deep well and a submersible pump. Plumbing and electricity are best left to the pros, especially when something like your well pump includes both. Even when troubleshooting your pump, it pays to have a partner standing by for your assistance and safety.

Well pumps need power to run, so they can’t function without electricity. If your power shuts off, there can sometimes be enough pressure in the water tank to allow for a lucky flush or a bit of tap water—but this won’t last long. It’s a good idea to have a backup generator or an alternative power source like solar if you’re worried about losing power.

There are many signs to look for that will tell you when your irrigation pump is burned out. This may include low water pressure, sprinklers that sputter a lot before turning on, discolored or dirty water, or a pump that stops working altogether. If your pump has any of these issues, it is probably time to replace it.

The average three to four-bedroom home typically uses a well pump rated for 8 to 12 gallons per minute (GPM). To find the most accurate size for your specific needs, a common rule of thumb is to count the number of water fixtures and appliances in your home and aim for that number in GPM. This calculation allows for about one gallon of water per minute per fixture. Because estimating the correct size can be challenging, it's best to have a professional technician make the final determination. A professional can ensure your pump provides sufficient water for your home, especially during peak usage hours.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

The Weldon, NC homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles