Top-rated well and pump technicians.

Get matched with top well and pump technicians in Red Banks, MS

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Red Banks, MS?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Red Banks, MS

*The Angi rating for Well And Pump Service companies in Red Banks, MS is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Red Banks, MS is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on November 19, 2025

Find Well and pump technicians in Red Banks

Avatar for Chief Purification Water Filter Systems

Chief Purification Water Filter Systems

No reviews yet

Chief Purification Water Filter Systems

No reviews yet
25 years of experience

Chief Purification is the only whole house water filter of its kind sold and manufactured individually. We also custom design filtration systems for Commercial and Industrial use. Our filters have been manufactured for over 40 years.

Chief Purification is the only whole house water filter of its kind sold and manufactured individually. We also custom design filtration systems for Commercial and Industrial use. Our filters have been manufactured for over 40 years.

Blue Water Paradise, Inc

5.00(
3
)

Blue Water Paradise, Inc

5.00(
3
)
Customers say: Quick response
Recommended by 100% of Angi customers
Recommended by 100% of HomeAdvisor customers

We have seasoned employee, contractors and subcontractors with extensive knowledge of the specific field in need. Our initial trip charge for a repair is 75.00 with a 45.00/hr rate on most quick turn hourly jobs. Most of our work is quoted as a complete turn key proposal and not hourly. New construction initial visit usually has no fee. We tackle jobs most contractors shy away from, and use products most contractors don't understand. The products we sell last so much longer, do a better job and cost less to operate therefore we do not have call backs that could cost you more money than the initial investment. We can provide a warranty others do not, such as a two year labor and three year product warranty on most of our equipment. We build it right. Our invoicing depends on the project. If it is hourly its due upon completion. Projects are on a draw basis usually four (4) draws 40%, 40% 15% 5%. This can vary. We are a Specialty Construction Company with in-ground pools and in-ground storm shelters. WE DIG IT!!! 4U.

We have seasoned employee, contractors and subcontractors with extensive knowledge of the specific field in need. Our initial trip charge for a repair is 75.00 with a 45.00/hr rate on most quick turn hourly jobs. Most of our work is quoted as a complete turn key proposal and not hourly. New construction initial visit usually has no fee. We tackle jobs most contractors shy away from, and use products most contractors don't understand. The products we sell last so much longer, do a better job and cost less to operate therefore we do not have call backs that could cost you more money than the initial investment. We can provide a warranty others do not, such as a two year labor and three year product warranty on most of our equipment. We build it right. Our invoicing depends on the project. If it is hourly its due upon completion. Projects are on a draw basis usually four (4) draws 40%, 40% 15% 5%. This can vary. We are a Specialty Construction Company with in-ground pools and in-ground storm shelters. WE DIG IT!!! 4U.

Hughes Brothers Plumbing Co. Inc.

4.50(
2
)

Hughes Brothers Plumbing Co. Inc.

4.50(
2
)
Customers say: Super punctual
Recommended by 100% of Angi customers
Recommended by 100% of HomeAdvisor customers

Hughes Brothers Plumbing Co. was incorperated in the state of Mississippi in 1987. Jimmy Hughes serves as president and Vice President is Phillip Hughes. Hughes plumbing began as a small plumbing repair company with four employees and gradually grew into a residential plumbing contractor in approximately five years. At the present time, Hughes Brother Plumbing Co., Inc. does ninety five percent commercial plumbing with only five percent residential and currently employs fifty full time employees. Hughes Brothers Plumbing Company's commercial projects include schools, motels and hotels, apartment complexes and factories.

Hughes Brothers Plumbing Co. was incorperated in the state of Mississippi in 1987. Jimmy Hughes serves as president and Vice President is Phillip Hughes. Hughes plumbing began as a small plumbing repair company with four employees and gradually grew into a residential plumbing contractor in approximately five years. At the present time, Hughes Brother Plumbing Co., Inc. does ninety five percent commercial plumbing with only five percent residential and currently employs fifty full time employees. Hughes Brothers Plumbing Company's commercial projects include schools, motels and hotels, apartment complexes and factories.

Showing 1-10 of 13
Wells and Pumps questions, answered by experts

Repair costs range from $200 to $1,200, depending on the issue and pump type.

A leaking well pipe is quite different from if the well itself is leaking. To seal a leaking well, pour a cement mixture or bentonite into the space between the well casing and the borehole wall. The heavier cement collects at the bottom to form a solid seal, pushing lighter materials like mud and fluids up toward the surface. Professional well installation companies have the equipment to do this properly. 

If you notice that your well pump runs continuously, it’s important to take action quickly to avoid further damage. A few common issues may be to blame for a continuously running well pump, such as mechanical damage, a faulty pressure control switch, low water level, prime loss, and leaking pipes and fixtures.

Yes, you can adjust your well pump pressure relatively easily by yourself. You’ll need to remove the cover from your pressure switch and adjust a nut that controls cut-in pressure. Learn more about how to adjust a well pump pressure switch with a step-by-step guide to setting your water pressure.

Most well pump pressure switches have a factory setting of 30 to 50 PSI. There’s some flexibility with this if you’d like a lower or higher water pressure, but remember that it should sit 2 to 3 PSI above your well tank’s general pressure setting.

The inside of your pressure switch cover will usually indicate minimum and maximum settings—going below and above the numbers might damage your well pump.

The Red Banks, MS homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles