Top-rated well and pump technicians.

Best well and pump technicians near Nesbit, MS

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Nesbit, MS?

Select your specific project to find the pro for you.

Top-Rated Well and pump technicians in Nesbit - Updated Nov 2026

Ken Tyler Plumbing
3.9(
114
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Nesbit, MS and surrounding areas

In business since 2007

Free estimates

Emergency services offered

"They were alright.  They were just really quick.  They ran around the house and looked at all the toilets, faucets and water fixtures.  They gave me a brief explanation of what they say as potential issues.  They tried to sell more service or product.  They ended selling us a garbage disposal unit.  It was expensive and the labor was as well.  I paid another $500 on top of the Big Deal to rebuild a toilet and install a new garbage disposal.  They just replaced the gasket on the toilet.  They replaced something on the water heater as well.  We had a few leaks after they left."
Recommended by81%of homeowners
Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,680
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Nesbit, MS and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
AA Plumbing
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Nesbit, MS and surrounding areas

In business since 2016

Free estimates

Credit card accepted

We're dedicated to providing our clients with the very best in service, installation, and repair for all phases of your plumbing needs. We specialize in a variety of residential services and take pride in the attention to detail put into each of the projects we're involved with. We're known for our quality work and the integrity of our business. We look forward to building long-term relationships with our clients, and guarantee your satisfaction. \n

Avatar for Welch’s Drain Services
Welch’s Drain Services
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Nesbit, MS and surrounding areas

Free estimates

Emergency services offered

Warranties offered

We specializing in comprehensive plumbing solutions for both residential and commercial needs. Our service offerings include, but are not limited to, drain clearing, installation of bathrooms (including tubs and toilets), and septic tank maintenance. One of our key differentiators is our commitment to 24/7 availability. Our customers can rely on us to address their plumbing emergencies at any hour, ensuring that we are always there when they need us.

Avatar for Freeman Innovations
Freeman Innovations
New to Angi
Well Pump - Install or Replace

Serving Nesbit, MS and surrounding areas

In business since 2025

Warranties offered

Offers commercial services

Freeman Innovations is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. We have accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Response time2 hrs
Showing 1-10 of 12
Wells and Pumps FAQs, answered by experts

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Most professionals recommend that a deep well pump shouldn’t run more than 10 hours consecutively before cycling off. Overworking the well pump beyond the recommended amount can prematurely wear out your pump and burn out the motor, which means replacing it more often than you otherwise should need to. Your well pump should also come with the manufacturer’s use and maintenance recommendations that are specific to the model.

The cost to replace a well-pump motor will depend on the size, but this repair is often as costly as installing a new pump. Generally, a well-pump replacement will cost between $950 and $2,650, with an average of $1,800. Other factors like pump type and pipework will impact your final cost.

A professional well inspection takes between one and three hours. This includes the time it takes for the inspector to visually check the condition of your well, test its equipment, and collect water for testing. After the pro sends the water samples to the lab, you can expect to receive the results in three to 10 days.

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

The Nesbit, MS homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.