Get matched with top drywall pros in Jetmore, KS

Q: What’s the easiest way to cut holes for electrical boxes in drywall?

• <div><p>The easiest way to cut holes in drywall for electrical boxes is to use a spiral saw with a drywall router bit. Hang the drywall without cutting out a hole for the box, but make sure you measure and mark where the box is located on the wall. Once you screw in the drywall sheet, drill a small hole into the box void, insert the spiral saw bit, and move it around the edge of the box using the inside wall as a guide. You can also use an oscillating multi-tool with an electrical box cutout for fast, professional results.</p></div>

Q: Should you skim coat plaster?

• <div><p>You can skim coat plaster, but it&rsquo;s better to repair the plaster itself. A skim coat is a thin coat of drywall joint compound spread over the surface of a wall. The result is a flat finish that looks pleasing, but part of the appeal of plaster is its imperfections and aesthetic. Skim coating is best when limited to drywall applications. </p></div>

Q: How much does it cost to replace a plaster ceiling?

• <div><p>If you already have plaster walls and ceilings, adding new plaster costs $2 to $10 per square foot. For an average-sized room, that would come out to $1,200 to $10,000. However, the <a href="https://www.angi.com/articles/cost-to-replace-plaster-with-drywall.htm">cost to replace plaster with drywall</a> is higher&mdash;running between $720 and $1,250 for a 10-by-8-foot wall or ceiling (not including drywall finishing). </p></div>

Q: Can you use drywall repair techniques on plaster?

• <div><p>Yes, you can use drywall repair techniques for some types of plaster damage. Tiny holes and small cracks in plaster can be patched in similar ways to drywall. You apply the necessary compound to fill the hole, wait for it to dry, then sand it down. For larger damage, like water damage or mold, you need to use plaster-specific techniques and materials. </p></div>

Q: How do you know if a wall is load-bearing?

• <div><p>The easiest way to <a href="https://www.angi.com/articles/load-bearing-wall.htm">tell if a wall is load bearing</a> is to check if it&rsquo;s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don&rsquo;t fit into these categories can still be load-bearing. If you&rsquo;re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.</p></div>

Enter your zip and get matched with up to 5 pros

Need a pro for your drywall service project in Jetmore, KS?

Select your specific project to find the pro for you.

Find Drywall pros in Jetmore

The Handy Guy - Home Facebook

4.9(

)

Serving Jetmore, KS and surrounding areas

In business since 2020

Free estimates

Emergency services offered

"There really isn't anything he can't do, I have hired him to do shed repair, guttering restoration, ideas for my patio & courtyard. He hung art for me, repaired the ceiling in the garage, repaired my fence, calked my bathtub. He will do the guttering next."

Response time3 days

Recommended by92%of homeowners

Serving Jetmore, KS and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Had to file a claim for new clothes dryer, and repairs on fridge. Foothills Star Appliance came to look at both. Eric was the repairman. He was friendly, answered all my questions, and very professional. I would highly recommend his company."

Recommended by82%of homeowners

Request Quote

Vantage Point Exteriors

3.8(

122

)

Serving Jetmore, KS and surrounding areas

In business since 2012

Free estimates

Emergency services offered

"Through Angie's List we found Vantage Point Exteriors and chose them to install James Hardie Siding on our house.
Matt at Vantage Point was a very helpful contractor. We could contact him at any time of the day.
He guided us through the many choices we needed to make, and showed us how our house would look with each decision.
He worked with the Hardie Company and put together a very professional team with knowledge of the product and a great work ethic. They were craftsmen, courteous, good problem solvers, and on time.
They provided an outcome that has rejuvenated our 40-year-old home into a showcase. There were no surprises or hidden costs. In short they were a delight to work with.
Sincerely,
Pam and Mike Bennett
Lenexa, Kansas
"

+38

Recommended by73%of homeowners

Request Quote

American Home Shield – Home Warranty

3.5(

5,688

)

Serving Jetmore, KS and surrounding areas

In business since 1971

Credit card accepted

"Very good. I use them for my rental property as well. Very good. Reliable. Cost is very appropriate for the service."

Recommended by65%of homeowners

Serving Jetmore, KS and surrounding areas

In business since 2023

Free estimates

Emergency services offered

I offer interior and exterior painting services, hauling, yard cleanup and more. Call or click today to schedule your free estimate!

Recommended by100%of homeowners

Request Quote

All Star Painting - Home Facebook

5.0(

)

Serving Jetmore, KS and surrounding areas

In business since 2009

Free estimates

Small jobs welcome

All Star Painting has been working in Kansas for more then a decade. Working on every project imaginable, from simple touch-ups to whole home paintjobs, and everything in between.

+19

Response time4 hrs

Recommended by100%of homeowners

Serving Jetmore, KS and surrounding areas

In business since 2023

Free estimates

Offers commercial services

J & C Remodeling LLC is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests and make their concerns the basis of our business. \n

Response time10 hrs

Response rate100%

Recommended by100%of homeowners

Request Quote

Hampton Enterprise LLC

3.7(

)

Serving Jetmore, KS and surrounding areas

In business since 1989

Free estimates

Emergency services offered

Our mission at Hampton Enterprise LLC is to provide clients with superior customer service, quality work and speedy service in all aspects of their home improvement needs. Licensed, insured and trusted since 1989; come discover the Hampton difference today!\n\nWe specialize in the installation and repair of Windows, Doors, Flooring, Sinks, Bathtubs, Showers, Sprinkler Systems and much more. We also offer Interior and Exterior Home Painting, Custom Welding Fabrication and Carpentry.Localy in your area just call and i will call back with a local number thank you . from James Hampton\n\nAL.Dothan 334-648-3817,\nAL Birmingham 334-648-3817,\nAL Huntsville 334-648-3817,\nAL Mobile 334-648-3817,\nAL Tuscaloosa 334-648-3817,\nAL Montgomery 334-578-4761,\nAR Little Rock 334-648-3817,\nAZ Phoenix 334-648-3817,\nCA LosAngeles/Sacramento 334-648-3817,\nCO Denver/Colorado Springs 334-648-3817,\nCT Hartford 334-648-3817,\nDE Dover 334-648-3817,\nFL Tallahassee 334-648-3817,\nFL Cape Canaveral/ Cocoa 334-648-3817,\nFL. Destin 334-648-3817,\nFL Gainsville 334-648-3817\nFl Jacksonville 334-648-3817,\nFL Orlando 334-648-3817,\nFL Panama City 334-648-3817,\nFL Tampa 334-648-3817,\nFL Miami 334-648-3817,\nGA Atlanta 334-648-3817,\nGA Albany 334-648-3817,\nGA Augusta 334-648-3817,\nGA Columbus 334-648-3817,\nGA Macon 334-648-3817,\nGA Valdosta 334-648-3817,\nIA Des Moines 334-648-3817,\nID Boise 334-648-3817,\nIL Chicago/Springfield 334-648-3817,\nIN Indianapolis 334-648-3817,\nKS Levenworth/Topeka 334-648-3817,\nKY Frankfort 334-648-3817,\nLA New orleans/Baton Rouge 334-648-3817,\nMA Boston 334-648-3817,\nMD Annapolis 334-648-3817,\nME Augusta 334-648-3817,\nMI Detroit/Lansing 334-648-3817,\nMN Saint Paul 334-648-3817,\nMO kansas City/Jefferson City 334-648-3817,\nMS Jackson 334-648-3817,\nMS Biloxi 334-648-3817,\nMS Gulf Port 334-648-3817,\nMT helena 334-648-3817,\nNC Raleigh 334-648-3817,\nND Bismark 334-648-3817,\nNE Lincoln 334-648-3817, \nNJ Trenton 334-648-3817,\nNM Santa Fe 334-648-3817,\nNV Carson City 334-648-3817,\nNV Las Vegas 334-648-3817\nNY Albany 334-648-3817,\nOH Columbus 334-648-3817,\nOK Oklahoma Ciy 334-648-3817,\nOR Salem 334-648-3817,\nPA harrisburg 334-648-3817,\nRI Providence 334-648-3817,\nSC Columbia 334-648-3817,\nSD Pierre 334-648-3817,\nTN nashville 334-648-3817,\nTX Austin 334-648-3817,\nUT Salt Lake City 334-648-3817,\nVA Richmond 334-648-3817,\nVT montpelier 334-648-3817,\nWI Madison 334-648-3817,\nWV Charleston 334-648-3817,\nWY Cheyenne 334-648-3817

Recommended by60%of homeowners

Request Quote

Starr Restoration, LLC

5.0(

)

Serving Jetmore, KS and surrounding areas

In business since 1996

Free estimates

Starr Restoration, LLC has been serving the Garden City, KS and surrounding areas for over fourteen years. Our specialty is restoration services, including, but not limited to, water. Call today!

+24

Recommended by100%of homeowners

Serving Jetmore, KS and surrounding areas

In business since 2022

Free estimates

We take great pride in our experience, expertise, quality, and customer service that we provide to meet the consumer's needs. It is our mission to provide excellent workmanship and complete customer satisfaction, from the start to the completion of a project. In order to understand the needs and expectations of our customers, we take great care to work and communicate with every customer in a professional manner. Our reputation is based on service, safety, and quality, regardless of how large or small the job.

Response time50 mins

Recommended by100%of homeowners

Request Quote

Showing 1-10 of 32

Drywall questions, answered by experts

The easiest way to cut holes in drywall for electrical boxes is to use a spiral saw with a drywall router bit. Hang the drywall without cutting out a hole for the box, but make sure you measure and mark where the box is located on the wall. Once you screw in the drywall sheet, drill a small hole into the box void, insert the spiral saw bit, and move it around the edge of the box using the inside wall as a guide. You can also use an oscillating multi-tool with an electrical box cutout for fast, professional results.

You can skim coat plaster, but it’s better to repair the plaster itself. A skim coat is a thin coat of drywall joint compound spread over the surface of a wall. The result is a flat finish that looks pleasing, but part of the appeal of plaster is its imperfections and aesthetic. Skim coating is best when limited to drywall applications.

If you already have plaster walls and ceilings, adding new plaster costs $2 to $10 per square foot. For an average-sized room, that would come out to $1,200 to $10,000. However, the cost to replace plaster with drywall is higher—running between $720 and $1,250 for a 10-by-8-foot wall or ceiling (not including drywall finishing).

Yes, you can use drywall repair techniques for some types of plaster damage. Tiny holes and small cracks in plaster can be patched in similar ways to drywall. You apply the necessary compound to fill the hole, wait for it to dry, then sand it down. For larger damage, like water damage or mold, you need to use plaster-specific techniques and materials.

The easiest way to tell if a wall is load bearing is to check if it’s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don’t fit into these categories can still be load-bearing. If you’re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.

The Jetmore, KS homeowners’ guide to drywall services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles

Lyle Hendriks
•
May 30, 2026May 30, 2026
How Much Does It Cost to Texture Drywall? [2026 Data]
Drywall texture can create an attractive finish and add dimension to your home’s walls. This guide breaks down the factors that influence the cost to texture drywall.
Taylor Freitas
•
May 30, 2026May 30, 2026
How Much Does Drywall Installation Cost? [2026 Data]
Installing drywall is the most common way to finish your home’s interior. Use this drywall installation cost guide to see what your project is likely to cost.
Haley Nothstein
•
May 30, 2026May 30, 2026
How Much Does Drywall Repair Cost? [2026 Data]
Whether you want to spruce up a few dents and dings or fix a large surface area, investing in drywall repair costs can return your walls to a smooth, flush look.
Stacey L. Nash
•
May 3, 2026May 3, 2026
Plaster vs. Drywall: Pros, Cons, and Costs
Understanding the plaster vs. drywall debate is key to giving your home’s walls the perfect finish. Learn more about the pros, cons, and costs with our advice.
Lauren Bongard
•
May 21, 2026May 21, 2026
Sheetrock vs. Drywall: What’s the Difference?
The terms drywall and Sheetrock are often used interchangeably, but one is a brand and one is a specific product. Find out which one you need in this guide.
Paige Bennett
•
May 3, 2026May 3, 2026
Should Drywall Be Butt Up Against a Wall?
Thick gaps and extra joint compound can alter the look of drywall. So, should drywall be butt up against a wall? Review this guide for seamless installation.