Top-rated concrete cutting pros.

Best concrete cutting pros near Collins, GA

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Collins, GA?

Select your specific project to find the pro for you.

Top-Rated Concrete cutting pros in Collins - Updated Nov 2026

Floors Sag or Shake
4.7(
129
)
Concrete Flatwork - Repair & Resurface

Serving Collins, GA and surrounding areas

In business since 1980

Free estimates

Credit card accepted

"Very well. The slight dip in the kitchen looks better and the doors trued up. The slight sag still in the kitchen floor is because of the sub floor plywood which I didn't want to get in to. They leveled the joist by shimming the tops of several cinder block posts and installing a pair permanent of steel posts under a section of joist the previous owner had cut in two."
Recommended by93%of homeowners
Avatar for AAA Basement Waterproofing
AAA Basement Waterproofing
4.8(
83
)
Concrete Flatwork - Repair & Resurface

Serving Collins, GA and surrounding areas

In business since 1995

Free estimates

Emergency services offered

"Overall, it was a good experience. AAA put down a vapor barrier and installed a Santa Fe dehumidifier with sump pump. The result is that we can now use the stand-up basement/crawlspace to store things under the house without ruining them. This is the part that you need to know. The installation was not without problems. First, they broke an A/C drain pipe, second, they cut a sprinkler controller wire while running a PVC pipe. Here's my take, accidents happen but how does the business respond to these issues? Well, Donna was very quick to send her team out to correct the problems and they even paid for the damage to the sprinkler system. To me, that's top notch customer service. Any business can make a mistake, but how they handle it is the mark of a good company. Every time I lift the roll door and go into the basement now, I'm amazed at how cool and fresh the air is down there. No more mildew and no more smell."
Full Interior Encap Sys
Full Interior Crawl Drainage Sys
Before Crawl Drainage System
Before Sub-Floor System
After Sub-Floor System

+5

Recommended by100%of homeowners
Avatar for Healthy-Crawl Space
Healthy-Crawl Space
4.7(
68
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For Business

Serving Collins, GA and surrounding areas

In business since 2008

Free estimates

Emergency services offered

"I called Crawlspace Doctor and the representative came and inspected our space later that day. I had received a strong recommendation on this co. from a friend. Our National termite control company had told us we needed some remedial work. The Crawlspace rep quoted me a price that day which was about 1/2 of the termite company for the same general work scope. I said to go ahead. Completely satisfied with the service."
Basement Waterproofing Project
Basement Waterproofing Project
Basement Waterproofing Project
Basement Waterproofing Project
Additional Photos

+6

Recommended by98%of homeowners
Avatar for Boucon USA
Boucon USA
4.3(
12
)
Concrete Flatwork - Repair & Resurface

Serving Collins, GA and surrounding areas

Emergency services offered

Credit card accepted

"It went very well. Boucon USA removed my original driveway, hauled off all of the spoils and poured my new driveway all in one day. Very professional and clean. I would be willing to hire them again for any concrete needs."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+1

Recommended by90%of homeowners
Avatar for American Handy Hands, LLC
American Handy Hands, LLC
5.0(
6
)
Concrete Flatwork - Repair & Resurface

Serving Collins, GA and surrounding areas

In business since 2021

Free estimates

Emergency services offered

"bathroom walk-in shower remodel???- I would highly recommend American Handy Hands to anyone. They did a walk-in shower for me for my disabled husband and then actually ended up doing more updating while they already here working. Dustin Collins was great at coming by and getting me a quote on my job and within a few days of the quote they were ready to start the job. The guys (Mike, Robbie and Jay) and Daniel (ceiling repair), I could not have not asked for any greater guys to have done the job. Everyone was a true blessing to me and my husband. I have already talked to Dustin about more jobs I am looking forward to him doing for me in the very near future. If you are needing anything done, please do not hesitate to give American Handy Hands a call. I don?t think you will be disappointed."
Sink Repair
Flooring Install
Shed Build Start
Shed Building
Framing

+3

...
Showing 1-10 of 52
Concrete Cutting FAQs, answered by experts

Yes, but you’ll need reliable steel-cutting tools and safety gear to get started. Shipping containers are typically around ¾ inch thick, so it’s entirely possible to cut through them, but experience and the right equipment are very important. When possible, try to get a container as close to the size you want it as possible.

You should not do your own welding unless you have the proper training and experience. Most home electrical systems can only handle MIG welding, which creates weaker bonds than TIG welding and won’t work on certain metals or metal thicknesses. Both welding forms usually require the use of shielding gas, which can be dangerous to store at home. Additionally, welding machines create temperatures of over 3,000 degrees, and the sparks can blind you if you don’t have the proper equipment. As such, it’s usually better to hire a professional welder for your welding projects.

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

The Collins, GA homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.