Top-rated concrete cutting pros.

Get matched with top concrete cutting pros in Brooklet, GA

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Brooklet, GA?

Select your specific project to find the pro for you.

TRUSTED BY BROOKLET, GA HOMEOWNERS

  • Average homeowner rating star icon4
    Average homeowner rating
  • Verified reviews icon23
    Verified concrete cutting services reviews

Verified Reviews for Concrete Cutting pros in Brooklet, GA

*The Angi rating for Concrete Cutting companies in Brooklet, GA is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Concrete Cutting needs.

*The HomeAdvisor rating for Concrete Cutting companies in Brooklet, GA is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Concrete Cutting needs.

Last update on June 01, 2026

Find Concrete cutting pros in Brooklet

Floors Sag or Shake
4.7(
129
)
Concrete Flatwork - Repair & Resurface

Serving Brooklet, GA and surrounding areas

In business since 1980

Free estimates

Credit card accepted

"Very well. The slight dip in the kitchen looks better and the doors trued up. The slight sag still in the kitchen floor is because of the sub floor plywood which I didn't want to get in to. They leveled the joist by shimming the tops of several cinder block posts and installing a pair permanent of steel posts under a section of joist the previous owner had cut in two."
Recommended by93%of homeowners
Request Quote
Avatar for Bowerman Removal Services - Home Facebook
Bowerman Removal Services - Home Facebook
4.7(
39
)
Concrete - Sawing or RemovalConcrete Flatwork - Repair & Resurface

Serving Brooklet, GA and surrounding areas

In business since 2020

Free estimates

Emergency services offered

"Very impressed from the start to finish. They were very careful cutting down the pine tree that was so close to the house using a bucket truck. Taking it down piece by piece. Ron was very Knowledgeable about Pecan trees and helped me make a decision to trim one our 100+ year old trees and saved it from toppling over. Will use them again."
Metal Roof Install
Metal Roof Install
Power Wash
Response time1 day
Response rate91%
Recommended by91%of homeowners
Request Quote
Avatar for AAA Basement Waterproofing
AAA Basement Waterproofing
4.8(
83
)
Concrete Flatwork - Repair & Resurface

Serving Brooklet, GA and surrounding areas

In business since 1995

Free estimates

Emergency services offered

"These workers are no strangers  to hard work. They performed this job under freezing temperatures and in a confined and dark area of my basement. They went to extra extremes and additional work to keep from tearing up my yard. The clean-up was outstanding. If you have a serious water problem in your basement, this is the company you want. Very thorough and detailed with expert knowledge. Simply explain your problem to them and sit back and relax knowing you can expect the best.
"
Full Interior Encap Sys
Full Interior Crawl Drainage Sys
Before Crawl Drainage System
Before Sub-Floor System
After Sub-Floor System

+5

Recommended by100%of homeowners
Request Quote
Avatar for Boucon USA
Boucon USA
4.3(
12
)
Concrete Flatwork - Repair & Resurface

Serving Brooklet, GA and surrounding areas

Emergency services offered

Credit card accepted

"It went very well. Boucon USA removed my original driveway, hauled off all of the spoils and poured my new driveway all in one day. Very professional and clean. I would be willing to hire them again for any concrete needs."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+1

Recommended by90%of homeowners
Request Quote
...
Showing 1-10 of 61
Concrete Cutting questions, answered by experts

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

The cost to weld aluminum averages about $14 to $22 per pound. The type of metal factors into the overall cost of any welding project due to the cost of the materials and the expertise required to work with it. Some of the most common metals used by welders include:

  • Magnesium alloy: $7–$16 per pound

  • Low-carbon steel: $11–$12 per pound

  • Stainless steel: $13–$15 per pound

  • Copper/brass: $24–$29 per pound

  • Cast iron: $38–$79 per pound

  • Titanium: $60–$85 per pound

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

The Brooklet, GA homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles