Top-rated concrete cutting pros.

Best concrete cutting pros near Eagle, CO

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Eagle, CO?

Select your specific project to find the pro for you.

Top-Rated Concrete cutting pros in Eagle - Updated Nov 2026

Avatar for ABT Construction
ABT Construction
4.8(
2
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For BusinessConcrete Flatwork - Repair & Resurface

Serving Eagle, CO and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"ABT is a Father-Son team. They are honest, hard-working, Knowledgeable, punctual, experienced, and a couple of good guys! They did what they said, they explained everything to me, and they got the job done under difficult circumstances (snow, cold, frozen ground, etc.). I’d hire them again! You should too?"
Step and Slab
Step and Slab
Concrete patch
Concrete crack patching
Concrete Driveway

+1

Response time3 days
Recommended by100%of homeowners
Avatar for Joel Valenti Industries
Joel Valenti Industries
3.7(
69
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For Business

Serving Eagle, CO and surrounding areas

In business since 1989

Credit card accepted

"The main problem with this contractor is with the subcontractors they use. The flooring people were great. The remodeling and painting people were not. The workmanship was not of high quality. We have had issues with the folding closet doors they installed -- one broke within two months of installation. When they originally installed them, they didn't paint the ends of the doors, so that showed when they were open. Then, when they came back to paint them, they knocked a hole in one of them and it had to be patched. You can still see the patch. The biggest issue has been with the egress window they installed in the sitting room adjacent to the bedroom. That room has been flooded TWICE in the less than two years since the remodel. The subcontractor who installed the window well did a poor job of it. We have had to remove the engineered hardwood floor twice and pay for water remediation both times. The first time it flooded, I called the contractor to inquire about warranties (it had only been a couple of months since installation), or to at least get contact information for the subcontractor. My call was never returned. Once they were paid for the job, they had no further interest in our satisfaction. Very disappointing."
Additional Photos
Additional Photos
Recommended by81%of homeowners
Showing 1-10 of 32
Concrete Cutting FAQs, answered by experts

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

The cost to weld aluminum averages about $14 to $22 per pound. The type of metal factors into the overall cost of any welding project due to the cost of the materials and the expertise required to work with it. Some of the most common metals used by welders include:

  • Magnesium alloy: $7–$16 per pound

  • Low-carbon steel: $11–$12 per pound

  • Stainless steel: $13–$15 per pound

  • Copper/brass: $24–$29 per pound

  • Cast iron: $38–$79 per pound

  • Titanium: $60–$85 per pound

Welders use a variety of methods in their trade. Different types of welding are better suited for different purposes and contexts. For example, stick welding is a versatile form suitable for most metals and alloys. The most common types of welding include:

  • Stick welding: $100–$1,000

  • Metal Inert Gas (MIG) welding: $250 and up

  • Tungsten Inert Gas (TIG) welding: $250 and up

  • Gas welding: $150 and up

  • Forge welding: $15–$25 per hour

The Eagle, CO homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.