Top-rated well and pump technicians.

Get matched with top well and pump technicians in Aniwa, WI

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Aniwa, WI?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Aniwa, WI

*The Angi rating for Well And Pump Service companies in Aniwa, WI is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Aniwa, WI is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on July 09, 2025

Find Well and pump technicians in Aniwa

Avatar for Dan's Service Plus LLC
Dan's Service Plus LLC
4.7(
36
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Aniwa, WI and surrounding areas

In business since 2005

Emergency services offered

Credit card accepted

"During the first year of home ownership, we encountered several plumbing and HVAC issues that needed to be addressed. We were assigned Dan's Service Plus through our home warranty company. Dan's Service Plus handled all of our issues very well. One of their service technicians, Chuck, was assigned to address most of our plumbing needs. He did a thorough job to fix the issues and never left a mess after he finished. We had also requested an estimate for a small renovation project as well as an estimate for a new furnace. Dan and Gregg came out to complete estimates right away. We will certainly keep them in mind when financial resources become available for the projects. Overall, we feel Dan's Service Plus has been very responsive, courteous and most of all they get the job done right. It's great to know a plumbing and HVAC company that we can trust in the Wausau area. Highly recommend!"
Recommended by94%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Aniwa, WI and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Normally, when your well pump turns on or off, you’ll hear a small click. This isn’t anything to worry about, but it can be a problem if it’s clicking continuously. This can indicate that the well pump is short cycling—the pump continuously turns on and off.

This can wear out the motor and provide uneven water flow. If this happens, you may need to get it looked at by a well pump professional to see if you need to repair the switch or pump.

The costs depend on whether you are buying into an existing well or starting from scratch. The average well drilling cost is between $25 and $60 per foot. The average cost to repair a well is between $350 and $1500. If you have a shared agreement and a community association, there will be additional legal and administrative fees. 

Although air in your water lines won’t affect the overall quality of your water, it will lead to problems with your well water system if not addressed. Over time, too much air in your water lines can create blockages in your pipes, cause insufficient water flow to your taps and appliances, loosen pipes, and potentially damage important components of your well including your well pump and pressure tank. 

If you notice that your well pump runs continuously, it’s important to take action quickly to avoid further damage. A few common issues may be to blame for a continuously running well pump, such as mechanical damage, a faulty pressure control switch, low water level, prime loss, and leaking pipes and fixtures.

The Aniwa, WI homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles