Top-rated welders.

Get matched with top welders in Verona, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Verona, VA?

Select your specific project to find the pro for you.

Find Welders in Verona

Grady's Painting Plastering/Construction
2.0(
174
)
Wrought Iron Fence - Repair or Weld

Serving Verona, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
Twisted Metal Iron Works
4.2(
22
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomMetal Structure or Object - Weld or Cut+4 more

Serving Verona, VA and surrounding areas

In business since 2004

Free estimates

Emergency services offered

"I called Richard at Twisted Metal around 11:30 to see if he would come look at the gate. He said he could come at 1:30 that same day, so I was thrilled. Not only did he look at it, but he also repaired the hinges during the same visit. This is a gate we have loved for years and now we will have it to enjoy for years to come, thanks to Richard. It is a challenge today to find someone who is willing to take on a small job, especially in such a timely manner. I would highly recommend his services with any iron works project."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by80%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Weld or Cut

Serving Verona, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"I had an unusual request when I called Mr. Perez, the owner of Eastcoast Welding and Fabricating. It was to weld or solder a very old halloween decoration that our family just couldn't say good-bye to. I met Mr. Perez in Ruckersville, where Eastcoast is located. He took our broken pumpkin and performed a miracle. One hour later he was back with our pumpkin looking better then ever. We are thrilled! Thank you Marcos Perez for accepting my challenge and for delivering such an unexpected "Bang for my Buck!" T.B. Spotssylvania, Va."
Response time2 days
Recommended by100%of homeowners
Showing 1-10 of 31
Welding questions, answered by experts

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

The Verona, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.