Top-rated welders.

Get matched with top welders in Crimora, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Crimora, VA?

Select your specific project to find the pro for you.

Find Welders in Crimora

Avatar for Liberty Forged Ironworks
Liberty Forged Ironworks
5.0(
6
)
Wrought Iron Fence - Repair or WeldMetal Stairs and Railings - RepairMetal Structure or Object - Create Custom+4 more

Serving Crimora, VA and surrounding areas

Approved

Super Service Award Winner

In business since 2014

Free estimates

Warranties offered

"Firstly, our stair rail is gorgeous. The interactions with Michael who fabricated the rail and Lauren who handles their administrative details were professional and timely. They were so friendly and warm and so easy to work with that I asked for a stack of business cards to tell my contacts about them. Beautiful rail, beautiful experience. Would rate them as a 10 on scale of 5!"
Philosophy Stone
Banana Table
Custom Crossguard
Fish in a Barrel
Custom Handrail

+28

Response time10 hrs
Response rate100%
1 neighbors recently requested a quote
Twisted Metal Iron Works
4.2(
22
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomMetal Structure or Object - Weld or Cut+4 more

Serving Crimora, VA and surrounding areas

In business since 2004

Free estimates

Emergency services offered

"I called Richard at Twisted Metal around 11:30 to see if he would come look at the gate. He said he could come at 1:30 that same day, so I was thrilled. Not only did he look at it, but he also repaired the hinges during the same visit. This is a gate we have loved for years and now we will have it to enjoy for years to come, thanks to Richard. It is a challenge today to find someone who is willing to take on a small job, especially in such a timely manner. I would highly recommend his services with any iron works project."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by80%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Weld or Cut

Serving Crimora, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"I had an unusual request when I called Mr. Perez, the owner of Eastcoast Welding and Fabricating. It was to weld or solder a very old halloween decoration that our family just couldn't say good-bye to. I met Mr. Perez in Ruckersville, where Eastcoast is located. He took our broken pumpkin and performed a miracle. One hour later he was back with our pumpkin looking better then ever. We are thrilled! Thank you Marcos Perez for accepting my challenge and for delivering such an unexpected "Bang for my Buck!" T.B. Spotssylvania, Va."
Response time2 days
Recommended by100%of homeowners
Showing 1-10 of 34
Welding questions, answered by experts

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

You should not do your own welding unless you have the proper training and experience. Most home electrical systems can only handle MIG welding, which creates weaker bonds than TIG welding and won’t work on certain metals or metal thicknesses. Both welding forms usually require the use of shielding gas, which can be dangerous to store at home. Additionally, welding machines create temperatures of over 3,000 degrees, and the sparks can blind you if you don’t have the proper equipment. As such, it’s usually better to hire a professional welder for your welding projects.

The Crimora, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.