Top-rated well and pump technicians.

Get matched with top well and pump technicians in Serafina, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Serafina, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Serafina, NM

*The Angi rating for Well And Pump Service companies in Serafina, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Serafina, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on May 25, 2026

Find Well and pump technicians in Serafina

Avatar for Art's Plumbing and Heating, Santa Fe, NM
Art's Plumbing and Heating, Santa Fe, NM
4.0(
4
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Serafina, NM and surrounding areas

In business since 2000

Free estimates

Emergency services offered

Hello, and welcome to Art's Plumbing and Heating & Cooling! We are a family-owned and operated air conditioning, furnace, plumbing and drain repair and installation company, and I would love for our team to have the opportunity to serve you! We take pride in offering the best customer service, the most technically trained service professionals and the friendliest team. EMERGENCY SERVICE AVAILABLE..

Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by100%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Serafina, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

Though sprinkler systems can have varying issues, there are a few common ways to know if the cause is your pump. Signs include cracking or visible damage, leaking from the pump, a pump that won’t turn on, and loud noises coming from your pump. Low or irregular pressure could also point to a pump problem, but there are other causes.

Yes, a bigger well pump can increase water pressure—up to a point. If you currently have a well pump of 8 GPM, you might notice a pressure boost when you go up to 10 GPM. However, overshooting significantly (going up to 15 GPM for an 8 GPM home) can strain your well system and result in things like burst pipes that can decrease your water pressure and make for costly repairs.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

If your water pump fails, the first step is to turn off the power to the pump to prevent any further damage. Check for common issues such as clogs, electrical problems, or mechanical failures. If you cannot identify the problem, contact a professional who specializes in pump repairs. Prompt action can help minimize damage and repair costs.

Age is certainly a factor in well pump failure. The older your pump, the more likely it is to fail. 

Beyond age, other factors can cause your well pump to fail, too. Things like poor water quality can cause sediment buildup in your pump. Without proper cleaning, your pump can seize up and fail. Having a dry well for too long can also cause your pump to fail, as it keeps working even though there's no water for it to pull. 

The Serafina, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles