Top-rated well and pump technicians.

Best well and pump technicians near Latimer, MS

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Latimer, MS?

Select your specific project to find the pro for you.

TRUSTED BY LATIMER, MS HOMEOWNERS

  • Average homeowner rating star icon4.4
    Average homeowner rating
  • Verified reviews icon35
    Verified well and pump services reviews

Top-Rated Well and pump technicians in Latimer - Updated Nov 2026

Avatar for AnB Plumbing Pros llc
AnB Plumbing Pros llc
4.5(
14
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Latimer, MS and surrounding areas

In business since 2022

Emergency services offered

Credit card accepted

"I was super impressed with the amazing job Andy did not to mention how quickly he got it done. He is well skilled and very smart learned a lot from him and would definitely hire him again. My buddy who owns rent houses also used Andy on a lot of jobs and always spoke highly of his work."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+38

Recommended by84%of homeowners
United Plumbing
3.7(
22
)
Well Pump - Repair or Service

Serving Latimer, MS and surrounding areas

In business since 2012

Free estimates

Emergency services offered

"They were very quick and professional. I wanted to upgrade to tankless water heater. They made it very simple and clean. Also it looks very nice instead of a clunky tank in a corner. Prices are very reasonable and affordable as well. I would highly recommend to anyone looking to upgrade their water heater."
Response time2 hrs
Response rate90%
Recommended by64%of homeowners
Showing 1-10 of 32
Wells and Pumps FAQs, answered by experts

If you’re going away on vacation or leaving your home for a long time, it’s a good idea to switch off your well pump and pressure tank before you go. This way you can prevent any damage from unexpected leaks that may occur or unforeseen electrical issues while you’re away.

Servicing includes cleaning filters and coils, checking coolant levels, and inspecting electrical connections.

Well pumps need power to run, so they can’t function without electricity. If your power shuts off, there can sometimes be enough pressure in the water tank to allow for a lucky flush or a bit of tap water—but this won’t last long. It’s a good idea to have a backup generator or an alternative power source like solar if you’re worried about losing power.

No, a larger well pressure tank will not increase your home's water pressure by itself. Water pressure is determined by the pressure control switch on the well pump.

However, a larger tank does offer other benefits. It can store more water, which allows you to run water for longer periods before the pump needs to turn on. This reduces how often the pump cycles on and off, leading to less wear and tear on the pump and the entire well system. Consequently, a larger tank can help extend the life of your equipment and may prevent future pump issues that could affect water pressure.

If your goal is to increase water pressure, consider these alternatives:

  • Adjust the pressure settings on your tank to a higher PSI (pounds per square inch).

  • Replace your current pump with a model that has a higher flow rate, measured in gallons per minute (GPM).

  • Have a professional install a water pressure booster pump in your plumbing system.

  • If you experience pressure fluctuations, consider upgrading to a constant pressure system.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

The Latimer, MS homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.