Top-rated well and pump technicians.

Get matched with top well and pump technicians in Fulton, MO

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Fulton, MO?

Select your specific project to find the pro for you.

Find Well and pump technicians in Fulton

Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,678
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Fulton, MO and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
Total Home Care Mid-MO
New to Angi
Well Pump - Repair or Service

Serving Fulton, MO and surrounding areas

In business since 2022

Free estimates

Emergency services offered

Total Home Care Mid-MO is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Balkenbusch Excavating, LLC
New to Angi
Well Pump - Install or Replace

Serving Fulton, MO and surrounding areas

In business since 1978

Free estimates

At Balkenbusch Excavating, LLC, we have been handling an ever increasing variety of excavating services including residential and commercial jobs of all sizes. The difference we strive toward is that we will handle even the largest of jobs with the same personal service you'd associate with a residential and simple job. Similarly we give your smaller and simpler residential orders the same importance we provide our larger commercial accounts. We know how important our work is and we know that whether we are working at a person's residence, office, workplace or shopping center, that we have to uphold our name and commitments.

Wells and Pumps questions, answered by experts

Frozen well pipes make themselves known quickly, as your faucets slow down to a trickle or shut down completely. If you notice a serious reduction in flow in the winter from toilets, showers, kitchen faucets, and other plumbing fixtures, a frozen pipe or two is to blame. Another tell-tale sign is frost or ice on exposed pipes outside. 

Both can deliver clean water to your taps, but well water and city water carry a few differences. City water is delivered and connected through a main water line, and it travels through a network of underground private and public pipes to service various buildings and structures once it’s been treated.

Well water is derived from dug or drilled wells that source groundwater from the water table. City water is often more expensive than well water, but it eliminates the need for you to test and treat your own well water.

Here are some signs of a bad well pump that a pro should look at: 

  • If your well pump isn’t pumping water, you could have a leak or malfunctioning pump on your hands. 

  • If your water pump runs nonstop, there might be a leak or problem with the pressure tank, which can cause the pump to fail. 

  • Low water pressure can happen because of your pressure tank, low-water levels, or a wrong-sized pump. 

  • Dirt or sediment in your water can be a problem with a powerful pump, damaged pump filter, or the pump’s location.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Why is my irrigation pump not pulling water?

There are a few reasons your irrigation pump isn’t pulling in water. You could have a clogged suction filter. You may have not properly primed your pump so air got stuck somewhere in the system. Your pump also won’t work properly if it has faulty or damaged pump components, like a pump motor or pressure switch.

The Fulton, MO homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.