Top-rated concrete cutting pros.

Best concrete cutting pros near Sandstone, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Sandstone, MN?

Select your specific project to find the pro for you.

Top-Rated Concrete cutting pros in Sandstone - Updated Nov 2026

Avatar for American Waterworks
American Waterworks
4.5(
173
)
Concrete Flatwork - Repair & Resurface

Serving Sandstone, MN and surrounding areas

Approved

In business since 1989

Free estimates

Warranties offered

"They did great. The entire surface was level and free from tripping hazards. It is important to have them seal the cracks because there will be water from snow melt and the concrete will move. This will get you the 5 yr warrantee just in case."
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
438 neighbors recently requested a quote
Recommended by91%of homeowners
Avatar for Simstone Concrete Works Inc.
Simstone Concrete Works Inc.
3.7(
19
)
Concrete Flatwork - Repair & Resurface

Serving Sandstone, MN and surrounding areas

In business since 1998

Credit card accepted

"Initial estimate was for the concrete tear out only. Emailed Ross for a side visit. He came the same day. Quoted $1700 ($1200 for 4 inch). After the tear out was done, I asked him to quote the class five preparation. We agreed on $1350 and the work was done the next day. Everything was done on time. He left the work side and street clean. Everything is ready for me to put the pavers down. Very nice to work with. Good job."
Additional Photos
Additional Photos
Additional Photos
Simstone Concrete Works Inc.
Simstone Concrete Works Inc.

+4

Recommended by75%of homeowners
Avatar for MINNESOTA HARDSCAPES LLC
MINNESOTA HARDSCAPES LLC
5.0(
3
)
Concrete Flatwork - Repair & Resurface

Serving Sandstone, MN and surrounding areas

Free estimates

Emergency services offered

Warranties offered

"We could not be happier with the outcome of this project! Keenan and his team saved us from a DIY project that we bit off more than we could chew. He came out and gave us a quote less than 24 hours after reaching out to him and was able to get started on the project the following weekend. He was willing to work with the materials we had already purchased saving us the headache of returning everything. When we ran into issues with our pavers he took it upon himself to remedy the issue with the home improvement store the materials were purchased through. Again, going above and beyond what was agreed upon. He was upfront with cost changes as the project progressed and was cognizant on where he could save us money. We would, with not doubt, hire Keenan again."
Concrete patio
Concrete patio
Paver Patio
Pavers and Hardscaping Project
Paver repair

+29

Recommended by100%of homeowners
Avatar for Edward LLC
Edward LLC
5.0(
1
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For BusinessConcrete Flatwork - Repair & Resurface

Serving Sandstone, MN and surrounding areas

In business since 2018

Free estimates

"Beautiful work and attention to detail on my remodel of an early 1900’s home in Cambridge. They did a unique stomp texture on the ceiling with a knockdown that resulted in a beautiful marble design. I have had a lot of compliments on this. The driveway and sidewalks were over excavated sand replaced and compacted. It has been a year now with no frost heave. Very happy with the results."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+6

Recommended by100%of homeowners
Showing 1-10 of 18
Concrete Cutting FAQs, answered by experts

Some welding projects, such as repairing pipes or fences, require travel, whereas others, like furniture repair, do not necessarily require the welder to come to you. Travel and overhead factor into the overall cost of your welding project. Some of the most common welding projects include:

  • Metal furniture repair: $35–$100

  • Pipe repair: $200–$1,000

  • Small gates: $550–$750

  • Fencing: $1,200–$1,800

  • Fabricated sheet metal welding: $750–$2,500

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

Since water heaters are primarily made of metal, they’re commonly accepted by scrap yards and collectors. Don’t expect to fetch a high price, though—water heaters are mostly steel and aluminum, which aren’t high-value metals. Some components are made of more valuable metals, like brass and copper, but they’re a small portion of the heater and won’t affect the price much.

The Sandstone, MN homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.