Top-rated concrete cutting pros.

Best concrete cutting pros near Saint Peter, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Saint Peter, MN?

Select your specific project to find the pro for you.

TRUSTED BY SAINT PETER, MN HOMEOWNERS

  • Average homeowner rating star icon4.7
    Average homeowner rating
  • Verified reviews icon28
    Verified concrete cutting services reviews

Verified Reviews for Concrete Cutting pros in Saint Peter, MN

*The Angi rating for Concrete Cutting companies in Saint Peter, MN is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Concrete Cutting needs.

*The HomeAdvisor rating for Concrete Cutting companies in Saint Peter, MN is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Concrete Cutting needs.

Last update on September 09, 2026

Top-Rated Concrete cutting pros in Saint Peter - Updated Nov 2026

Avatar for American Waterworks
American Waterworks
4.5(
173
)
Concrete Flatwork - Repair & Resurface

Serving Saint Peter, MN and surrounding areas

In business since 1989

Free estimates

Warranties offered

"They did great. The entire surface was level and free from tripping hazards. It is important to have them seal the cracks because there will be water from snow melt and the concrete will move. This will get you the 5 yr warrantee just in case."
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
514 neighbors recently requested a quote
Recommended by91%of homeowners
Request Quote
Graystone Concrete & Masonry, LLC
New to Angi
Concrete - Sawing or Removal- For Business

Serving Saint Peter, MN and surrounding areas

In business since 2009

Free estimates

GrayStone Concrete & Masonry, LLC, is your 1st and finest choice in concrete and masonry, all right here in our community. GrayStone Concrete and Masonry, LLC, produces elegant concrete and masonry work. Producing the ultimate in quality craftsmanship, with pride in doing great work, we care for your place and your project, as if it was our own. We are your one-stop shop serving the complete project, even aspects not noticeable -- we allow the whole to be completed right when it should be. Rest assured and everything is good with GrayStone Concrete & Masonry, LLC. We are perfectionists and all of our work is guaranteed. Call now.

Request Quote
Showing 1-10 of 15
Concrete Cutting FAQs, answered by experts

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

The Saint Peter, MN homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles