Top-rated concrete resurfacing pros.

Best concrete resurfacing pros near Mcgregor, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete resurfacing project in Mcgregor, MN?

Select your specific project to find the pro for you.

Top-Rated Concrete resurfacing pros in Mcgregor - Updated Nov 2026

Avatar for American Waterworks
American Waterworks
4.5(
173
)
Concrete Flatwork - Repair & ResurfaceConcrete Flatwork - Repair & Resurface- For Business

Serving Mcgregor, MN and surrounding areas

In business since 1989

Free estimates

Warranties offered

"They did great. The entire surface was level and free from tripping hazards. It is important to have them seal the cracks because there will be water from snow melt and the concrete will move. This will get you the 5 yr warrantee just in case."
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
546 neighbors recently requested a quote
Recommended by91%of homeowners
Avatar for Simstone Concrete Works Inc.
Simstone Concrete Works Inc.
3.7(
19
)
Concrete Flatwork - Repair & ResurfaceConcrete Flatwork - Repair & Resurface- For Business

Serving Mcgregor, MN and surrounding areas

In business since 1998

Credit card accepted

"Initial estimate was for the concrete tear out only. Emailed Ross for a side visit. He came the same day. Quoted $1700 ($1200 for 4 inch). After the tear out was done, I asked him to quote the class five preparation. We agreed on $1350 and the work was done the next day. Everything was done on time. He left the work side and street clean. Everything is ready for me to put the pavers down. Very nice to work with. Good job."
Additional Photos
Additional Photos
Additional Photos
Simstone Concrete Works Inc.
Simstone Concrete Works Inc.

+4

Recommended by75%of homeowners
Showing 1-10 of 13
Concrete Resurfacing FAQs, answered by experts

A concrete overlay on an existing slab can range from 1/4 of an inch to 2 inches thick, though a minimum of 2 inches is often recommended to ensure stability and quality. The ideal thickness depends on the condition of the existing concrete and the depth of any planned designs or imprints. Before applying the overlay, it's important to repair and clean the surface, then apply a primer. For specialized work like a stamped concrete overlay, hiring an experienced contractor is recommended to determine the correct thickness and ensure the new layer isn't too high or heavy. For context, most standard concrete slabs are between 4 and 6 inches thick.

By reinforcing with fibers, sealing surfaces, and ensuring correct drainage.

Mix the resurfacer into a sticky mixture. The consistency should look like mashed potatoes. Use a squeegee to push the resurfacer across the pitted area and smoothen the surface with a cement trowel flush. Make sure you protect any expansion joints with a weather strip. Alternatively, cut out any resurfacer that touched the joint once the mixture begins to harden.

While certain kits make DIY possible, professionals ensure durability and quality of finish, which is vital for high-moisture areas like baths.

Concrete blemishes such as chipped steps or small cracks are fixable with patching. For bigger jobs, including driveway repair and cracks wider than a 1/4 of an inch, patches will only serve as a temporary fix. Resurfacing is ideal when the surface is showing more widespread wear—like if it’s pitted, rough, or has lots of cracks. Resurfacing gives your concrete a fresh, like-new appearance without needing a full replacement.

When the concrete is severely cracked, sinking, or otherwise structurally unsound, replacing it might be your best option. Replacement ensures the safety and longevity of the surface in this case.

The Mcgregor, MN homeowners’ guide to concrete resurfacing

From average costs to expert advice, get all the answers you need to get your job done.