Top-rated deck cleaning pros.

Get matched with top deck cleaning pros in Quartzsite, AZ

Enter your zip and get matched with up to 5 pros

Need a pro for your deck cleaning project in Quartzsite, AZ?

Select your specific project to find the pro for you.

Find Deck cleaning pros in Quartzsite

Avatar for National Property Inspections
National Property Inspections
4.7(
7
)
Deck, Fence, Patio or Porch - Clean and SealDeck, Fence, Patio or Porch - Clean and Seal - For Business

Serving Quartzsite, AZ and surrounding areas

In business since 2006

Free estimates

Emergency services offered

"I chose them because the pitch man convinced me they were the best and they were $260  while others I called were $300 and adding termite inspection was $325 and his was included in the $260. On Monday morning at 8am of the planned inspection day, we found the 'current' owner had not turned the electricity on thus, the inspection could not take place. We were emailed the bill would be an additional $65 for the trip charge as it was a good 100 miles round trip and our error, not theirs. I felt bad so I accepted the additional charge. There went my saving a buck. Next we were emailed a new appointment day, Thursday at  11am. The inspector arrived Thursday at 8am.  Needless to say, it confused my whole day arriving three hours early. The inspector really did a good job, explaining everything to me so that I understood. Then he presented me with a $325 bill that we had agreed on and I paid. It being early in the morning I wasn't thinking clearly but later I called the business office and said  -  "Since we have an email stating 11am and the inspector showed up at 8am, your mistake, so I should get my $65 back from the trip charge when it was our mistake." The business office wanted nothing to do with that idea. The $65 was for the extra time and mileage, she said. What about the disruption to my schedule showing up at the wrong time. It didn't matter. Every other time I spoke with the woman in the office she was very kind but suddenly she wasn't any more.  Because they strictly wouldn't change the bill when it was their fault and because they are so far away, I will not use this company again.
"
NPI- Experience the Difference
Recommended by85%of homeowners
Deck Cleaning questions, answered by experts

Most building codes require that railing spindles (also known as balusters) on decks or stairs be spaced no more than four inches apart. This safety standard is often called the '4-inch sphere rule,' which means a sphere with a 4-inch diameter should not be able to pass through the opening between balusters. This rule is in place to prevent small children and pets from slipping through the railing. For the same reason, the space between the bottom rail and the deck or floor surface should also be no more than four inches. As a general guideline, professionals often install three balusters per foot of railing. However, since specific requirements can vary by location, it is essential to check your local building codes to ensure compliance before starting your project.

Your deck may look or feel fuzzy after pressure washing because the high-pressure spray tears some wood fibers as it removes the outer layer of dead and discolored wood. This fuzzy effect is a normal part of the pressure-washing process and will go away on its own in a few weeks. You can opt to spot-sand your deck if you’d like to remove it more quickly.

It’s best to prime composite decking before painting. This promotes better paint adhesion, helps create a smooth finish, and can mean the paint job will last longer. Always follow the manufacturer’s instructions for application, allow ample primer drying time before painting (typically 24 to 48 hours), and thoroughly clean the deck boards to promote the best adhesion.

PVC decking can get slippery when wet because it’s made from plastic. However, composite and wood decking can also be slippery when wet. It’s best to wear shoes with grippy soles when walking on a wet deck, no matter the material, and to be extra cautious not to slip and fall down.

To flatten a cupped deck board, start by ensuring it’s dry. Then, try flipping the board over so the cupped side faces down and reattach it. If that’s not possible, you can use screws to pull it tighter to the joists or plane the edges slightly to reduce the cup. It’s best to replace severely cupped boards.

The Quartzsite, AZ homeowners’ guide to deck cleaning services

From average costs to expert advice, get all the answers you need to get your job done.