Top-rated contractors.

Best contractors near Parowan, UT

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Parowan, UT?

Select your specific project to find the pro for you.

Top-Rated Contractors in Parowan - Updated Nov 2026

Avatar for JC builders and construction
JC builders and construction
5.0(
5
)
Major Home Repairs (General Contractor)

Serving Parowan, UT and surrounding areas

In business since 2022

Free estimates

Credit card accepted

"I have had the opportunity to work with JC builders on a few different project's and There work is through and clean. They are qualified contractors and they do an excellent job from the framing to the drywall and paint. They did the remodel in my previous home which was a model home and I couldn’t have been happier with how it turned out. They built a beautiful outdoor wood deck for my father in law a few months ago complete with wood burning and stain. Thank you JC Builders you guys are the best!"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+8

Recommended by100%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Parowan, UT and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Parowan, UT and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for AT4 Construction LLC
AT4 Construction LLC
5.0(
2
)
Major Home Repairs (General Contractor)

Serving Parowan, UT and surrounding areas

In business since 2024

Free estimates

Offers commercial services

"Punctual. Reliable. Answered questions clearly. Stayed within the estimate. Cleaned up when leaving the job site. Excellent work and work ethic. We are very happy with their job and our "new" driveway. Highy recommend."
Hambilin Cabin
Hambilin Cabin
Response time1 day
Showing 1-10 of 27
Unfinished Carpentry FAQs, answered by experts

It’s sometimes safe to replace a load-bearing wall with a beam, but you need a structural engineer to sign off on the project. You’ll also likely have to upgrade to a steel I-beam or another material that’s stronger than wood to maintain the level of support you need without the wall underneath.

Installing a tongue-and-groove wall requires similar techniques to those associated with installing shiplap. However, because of the precision necessary to make each board fit perfectly and the increased material prices, the cost is higher than that of shiplap installations. Expect to spend between $2 and $6 more per square foot for tongue-and-groove walls versus shiplap ones.

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

You should avoid drilling or cutting into load-bearing beams because removing material will weaken it and increase the risk of structural damage or even collapse. If you do need to drill into a load-bearing beam, speak with a structural engineer first to discuss where it’s safest to drill and the width and depth of the bit that’s safe to use.

While some highly experienced homeowners can frame a house independently, it is not advisable. You will need ample carpentry experience, a team of helpers, and professionals to sign off on your work to meet local building codes. For the safest outcome, we recommend buying or building a house with the guidance of professionals.

The Parowan, UT homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.