Top-rated woodworkers.

Best woodworkers near Glendale, OR

Enter your zip and get matched with up to 5 pros

Need a pro for your woodworking project in Glendale, OR?

Select your specific project to find the pro for you.

Top-Rated Woodworkers in Glendale - Updated Nov 2026

Avatar for Eagle Point Building Services
Eagle Point Building Services
4.9(
34
)
Arbor, Pergola or Trellis - Build CustomArbor, Pergola or Trellis - Build Custom - For BusinessCarpentry Framing - Install+6 more

Serving Glendale, OR and surrounding areas

Approved

Super Service Award Winner

In business since 1981

Free estimates

Small jobs welcome

"The whole process of rebuilding the deck on our new home was completed very professionally from start to finish. We appreciated Curtis's attention to detail and providing a cost saving estimate before we committed to the job. The job was completed in just a few days and is outstanding. I would recommend Curtis to anybody looking for repair work or a new addition to their home."
Before
After
Wolske
Wolske
Foundation Setup

+19

Response time1 day
Response rate92%
3 neighbors recently requested a quote
Avatar for Nathan Henry
Nathan Henry
New to Angi
Closet - BuildCustom Cabinets - BuildInterior Trim and Decorative Moldings - Install+3 more

Serving Glendale, OR and surrounding areas

Approved

In business since 2019

Free estimates

Offers commercial services

Nathan Henry specializes in high-quality home repair and carpentry services for homeowners who value skilled workmanship and reliable results. Each project is approached with care, clear communication, and attention to detail, whether it’s a small repair or a more involved improvement. The focus is on doing the work correctly and cleanly—no shortcuts—so repairs last and your home is left better than it was found. Homeowners choose Nathan Henry for professional service, thoughtful execution, and work they can feel confident in.

1950's Stair Restoration
1950's Stair Restoration
1950's Stair Restoration
1950's Stair Restoration
New

+2

1 neighbors recently requested a quote
Avatar for Berper Construction LLC
Berper Construction LLC
5.0(
8
)
Arbor, Pergola or Trellis - Build CustomArbor, Pergola or Trellis - Build Custom - For BusinessCarpentry Framing - Install+10 more

Serving Glendale, OR and surrounding areas

In business since 2020

Free estimates

Emergency services offered

"We highly recommend Berper Construction LLC. We listed our project on Angi and literally 5 minutes later we received a call from Gerardo to set up an appointment to look at and give us an estimate. He came over that same day and sent us a bid the very next day. We accepted him and his team to do the work and just over a week later once we got our funds together, they began working on our project and were finished in 2 days! He was very thorough explaining what needed to be done and sent us pictures from Home Depot of different items we needed for the job and let us pick out exactly what we wanted. Always on time, very kind, and honest which is much appreciated. Gerardo made sure that he did the job exactly how we wanted and never did anything without getting our approval first. We love our 9x9 pergola over our hot tub, thank you Gerardo, Edwin, and the rest of your team! We will definitely call again for other projects in the future! :)"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+38

Recommended by100%of homeowners
Avatar for C&S Contracting
C&S Contracting
5.0(
7
)
Carport (Wood) - Build

Serving Glendale, OR and surrounding areas

In business since 2000

Free estimates

Emergency services offered

"Truly one of the most professional and hard-working contractors I have seen. They have been very thorough with the job, the preparation to paint on our old house that has been needing a new coat of paint for a long time has been extensive and most certainly not haphazard. There are so many different places where the wood has rotted out and they continue to take that all out and replace where needed like a professional job should be done. I have seen many contractors brush these types of things over due to the extra amount of work it takes, but that is not these guys. This company will make sure a job is done right! On a personal note, I also have a baby I need to put down for a nap each day, and they have been so understanding to work on the other side of the house and keep quiet until my baby wakes up. HUGE thank you to this company and their skill, professionalism, and positive attitudes."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+9

Recommended by100%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)
Furniture - Build Custom

Serving Glendale, OR and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
...
Showing 1-10 of 62
Woodworking FAQs, answered by experts

Most contractors do not charge for meetings, but it can depend on the project, mainly if it includes detailed consultations or project planning. For general estimates, homeowners shouldn't expect to be charged. Always ask up front about meeting fees to avoid surprises and ensure you know what’s included in the process.

Board and batten is a type of wainscotting that uses wider boards that are placed vertically, and it has a much more rustic aesthetic than wainscotting. Common wainscotting styles are raised-panel, flat-panel, and beadboard. Wainscotting is more intricate and will typically use more elegant, subtle trims compared to the more farmhouse-inspired boards of board and batten styles.

When building a house, it is customary to use 16d nails that measure 3 1/2 inches in length to construct the frame. These nails are crucial in providing the necessary support and stability for structural elements like joists and studs, which ensures a sturdy framework.

It is not recommended to cut or drill into LVL (laminated veneer lumber) beams. As major structural components of a home, their composite structure can be compromised by alterations, which can weaken them and lead to cracking over time. If you must make modifications to an LVL beam, it is crucial to consult a structural engineer or general contractor first. A professional can advise on whether it's safe and provide specifics on the appropriate bit size, depth, and directionality for any necessary drilling.

Yes, Corian® and other solid surface materials can be cut with standard woodworking tools, such as a circular saw or a jigsaw. However, it is crucial to use the correct type of blade to avoid damaging the material.

For a circular saw, a tungsten carbide-tipped blade is required; a triple chip grind blade is highly recommended. For a jigsaw, you should use a fine-tooth down-cutting blade. Do not use blades designed for cutting wood, as they can cause microfractures that weaken the edges of the countertop. A diamond blade is also unnecessary, as those are designed for harder materials like natural stone, which Corian is not.

After cutting, the edge will be rough. It is essential to sand and smooth the cut edge to prevent microfractures, which can eventually compromise the integrity of the countertop.

The Glendale, OR homeowners’ guide to woodworking services

From average costs to expert advice, get all the answers you need to get your job done.