Top-rated welders.

Get matched with top welders in Marietta, OK

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Marietta, OK?

Select your specific project to find the pro for you.

Find Welders in Marietta

Shepherd's Welding
5.0(
1
)
Metal Structure or Object - Weld or CutMetal Structure or Object - Create CustomWrought Iron Fence - Repair or Weld+2 more

Serving Marietta, OK and surrounding areas

Approved

Free estimates

Emergency services offered

Small jobs welcome

"Jacob responded very quickly. I sent photos to him. His quote was 1/3 that of another Angi contractor quote. Once scheduled, he arrived on time and finished the job within a few hours. He explained the work before, during, and upon completion. Excellent work! I hope we don't need future fence repairs or welding but I'll call Jacob at Shepherds Welding if we do."
36 neighbors recently requested a quote
Avatar for Load Bearing Beam Masters
Load Bearing Beam Masters
5.0(
6
)
Steel Beams (Structural) - Install

Serving Marietta, OK and surrounding areas

Approved

In business since 2023

Free estimates

Emergency services offered

"Jordan and his awesome team removed the shoddy work of a previous carpenter and professionally installed the proper steel I beams across our recently remodeled home. Three load bearing walls had been removed and the less than adequate work of our previous contractor had begun to leave our roof and ceilings sagging below the maximum allowed measurements and was causing large cracks in our ceiling and walls. Jordans crew jacked everything back up to its original position while attaching the rafters to the new beams… An awesome job by Jordan and his crew. We can now rest easy as we work to restore our ceilings, assured that the dangerous situation we were left with previously has been properly corrected! Thank you so very much Load Bearing Beam Masters!!"
Response time4 hrs
11 neighbors recently requested a quote
Recommended by66%of homeowners
Buckin' A Welding
0.8(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomSheet Metal and Ornamental Metal - Fabricate+3 more

Serving Marietta, OK and surrounding areas

Approved

Recently relocated to Grayson County. We've been serving Texas and other states for 13 years in building ground up commercial buildings, additions, and renovations. We specialize in structural steel fabrication and erection, custom steel fabrication, gates and entryways. We were designing and building Barndominiums before people knew what they were. We do the job right or not at all. We guarantee our work, and we often takeover failing or abandoned projects and get the project completed. We've built and have tore down and rebuilt many very large churches. We've done a lot of historical renovations and dealt woth the historical regulations, etc. We've done a lot of work at The Grandscape in The Colony Tx. We worked on The Dallas Morning News, The Statler Hotel as well as many other hotels, high end retail and entertainment districts. \n We have worked and a General contractor holding responsibility for a project from conception to planning and development, through completion.

...
Showing 1-10 of 78
Welding questions, answered by experts

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

The Marietta, OK homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.