Top-rated well and pump technicians.

Best well and pump technicians near Laughlin, NV

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Laughlin, NV?

Select your specific project to find the pro for you.

Top-Rated Well and pump technicians in Laughlin - Updated Nov 2026

Avatar for USA Plumbing and Septic, LLC
USA Plumbing and Septic, LLC
4.9(
7
)
Well Pump - Repair or Service

Serving Laughlin, NV and surrounding areas

Approved

In business since 2023

Free estimates

Emergency services offered

"The team at USA Plumbing and Septic were very responsive and professional. They did a great job I can not thank them enough. Even more importantly they answered they're phone"
Response time3 hrs
12 neighbors recently requested a quote
Recommended by83%of homeowners
Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,680
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Laughlin, NV and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
Dino's Plumbing - Home Facebook
New to Angi
Well Pump - Repair or Service

Serving Laughlin, NV and surrounding areas

In business since 2000

Call Plumbtec Mechanical if you�re looking for a company in the Las Vegas area to take care of your heating or plumbing repair needs. One phone call and one of our highly trained technicians will arrive promptly to get the job done, and leave the place cleaner than he found it. Satisfaction is guaranteed. When you invest your time and hard-earned money in home repair or maintenance, you deserve to receive the highest-quality service. When you choose us you are not just hiring a service technician, you're getting peace of mind. Every customer is protected by our 100% satisfaction guarantee!

Wells and Pumps FAQs, answered by experts

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

Common signs that your well pump is failing include fluctuating or consistently poor water pressure, sputtering water from faucets, or a complete loss of water. Other indicators are unusual noises coming from the pump, the pump running continuously, dirty or cloudy water, or a sudden, unexplained spike in your utility bills. While some issues, especially after a power outage, might be resolved by simply restarting the power or priming the pump, persistent problems suggest a more serious issue. If you notice any of these red flags, it is recommended to call a professional well pump service to inspect the system and determine whether it needs to be repaired or replaced.

If your well pump gets stuck in its casing, you may be able to free it loose by gently wiggling the line or by vibrations from tapping the line with a hammer. However, if your pump is stuck in a buildup of minerals around the casing, you’ll probably have to call in a well pump contractor to get it out. They’ll likely use a muriatic acid solution—a strong, corrosive acid—to break down the minerals and free the pump loose. 

To avoid a stuck pump in the future, experts recommend a professional well cleaning once every 10 years. 

Normally, when your well pump turns on or off, you’ll hear a small click. This isn’t anything to worry about, but it can be a problem if it’s clicking continuously. This can indicate that the well pump is short cycling—the pump continuously turns on and off.

This can wear out the motor and provide uneven water flow. If this happens, you may need to get it looked at by a well pump professional to see if you need to repair the switch or pump.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

The Laughlin, NV homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.