Top-rated masons.

Get matched with top masons in Lisbon, NH

Enter your zip and get matched with up to 5 pros

Need a pro for your masonry work project in Lisbon, NH?

Select your specific project to find the pro for you.

Find Masons in Lisbon

Avatar for Your Chimney Doctor
Your Chimney Doctor
4.9(
16
)
Brick or Stone - Tuck-pointingBrick or Stone - Tuckpointing - For Business

Serving Lisbon, NH and surrounding areas

Approved

In business since 2021

Free estimates

Emergency services offered

"Joshua did an incredible job rebuilding and repairing our chimney during a major renovation. The work was done carefully, cleanly, and with a clear understanding of both structural integrity and safety. He explained what needed to be done, why it mattered, and made sure everything was done the right way—not rushed. Seeing the finished brickwork framed into the new space gave us a lot of confidence moving forward with the rest of the project. Professional, knowledgeable, and dependable from start to finish. Highly recommend."
Chimney Doctor
Mailbox rebuild
Restack & Rebuild
Garage Rebuild
Full grind & repoint

+8

12 neighbors recently requested a quote
Avatar for HANDY ANDY SPECIALTY SERVICES LLC
HANDY ANDY SPECIALTY SERVICES LLC
4.9(
10
)
Brick or Stone - Tuck-pointing

Serving Lisbon, NH and surrounding areas

Approved

In business since 2024

Free estimates

Small jobs welcome

"I had them do a cleaning and inspection of my chimney and they found damages to the brickwork and the top of the chimney. They installed a new cap and their cost was so reasonable. All their work is guaranteed as well, which is reassuring. They were clean, efficient and courteous. I would highly recommend Handy Andy and in fact they are doing an estimate for my neighbor to whom I recommended them to."
11 neighbors recently requested a quote
...
Showing 1-10 of 84
Masonry questions, answered by experts

Brick spalling—which refers to the crumbly, flaky, or pitted appearance that can develop over time—is caused by a few different conditions. These include:

  • Climates with constant freeze-thaw cycles

  • Use of non-breathable sealants

  • High-pressure water cleaning

  • Improper installation

While you can’t do anything about the weather, you can preserve your bricks by cleaning them with soapy water and a good old-fashioned scrubbing. Pressure washers may be satisfying to use, but they can eventually wear away the surface of your bricks. If you don’t have advanced-level DIY skills in masonry, you can hire a reputable masonry contractor in your area for your project.

Painted exterior brick does not usually need sealing. Brick is a porous material, so you don’t want to apply a sealant that could trap moisture inside the bricks and cause erosion and structural damage. The risk of moisture-induced damage after sealing is higher in colder climates where trapped moisture can expand if it freezes. On the other hand, it makes sense to seal really old brick or kitchen backsplashes, where moisture from cooking can weaken the brick.

Yes, it is essential to prime or seal a brick fireplace before painting. Brick is a porous and highly absorbent material, so without a primer, paint can seep into the surface, resulting in uneven coverage and allowing the natural brick color to show through. To avoid this, apply one or two coats of a masonry primer. The primer will seal the brick and provide a smooth, uniform layer for the paint to adhere to. Ensure the primer is completely dry before applying the topcoat of paint.

You should generally drill into the mortar joints when installing shutters on brick. Mortar is softer, which makes drilling easier and puts less strain on your tools. It also lowers the risk of cracking a brick—something that’s a lot harder to fix. Mortar holds fasteners well enough for standard shutters, and if you ever need to patch the holes later, it’s a much simpler job than dealing with damaged brick. Just keep in mind that if your mortar joints are too thin or the hardware calls for brick anchoring, you'll need to check the manufacturer’s recommendations and adjust accordingly.

No, you don’t need to soak the brick before cutting it by hand. In fact, cutting a wet brick can make it harder to see your score lines and may cause the chisel to slip. Soaking is sometimes used with power tools to reduce dust, but for hand-cutting, it’s best to work with dry bricks for better control and visibility.

The Lisbon, NH homeowners’ guide to masonry services

From average costs to expert advice, get all the answers you need to get your job done.