Top-rated welders.

Get matched with top welders in Stedman, NC

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Stedman, NC?

Select your specific project to find the pro for you.

Find Welders in Stedman

Avatar for HF Custom Welding
HF Custom Welding
5.0(
16
)

Serving Stedman, NC and surrounding areas

In business since 2017

Free estimates

Credit card accepted

"Professional, quality workmanship, up front prices, did touch up work not requested neither charged. I wish I had more iron work to call them back again. I definitely will recommend them to anyone who needs a welder and will use them in the future should I have a problem they can fix."
Entry door handrail
Entry door handrail
Spot weld repairs
60’s ford door
60’s ford door

+22

Response time3 hrs
Response rate93%
Recommended by100%of homeowners
Avatar for ADaniel Performance Welding
ADaniel Performance Welding
5.0(
1
)

Serving Stedman, NC and surrounding areas

In business since 2020

Free estimates

Credit card accepted

"I needed a rear bumper replaced on my 1997 Airstream Excella. The original rubber was cracked from dry rot. There is storage below the bumper. I ask AJ if he could come look at it. He fabricated the top of the bumper and coated it with a rubber sealant. I'm very happy with the results."
Airstream Camper Repair
Bench Mount Metal Bender
Bench Mount Metal Bender
Airstream Camper Repair
Dump Trailer Hinge Repair

+4

Response time3 hrs
P & S Welding and General Maintenance
5.0(
1
)

Serving Stedman, NC and surrounding areas

In business since 1996

Free estimates

Offers commercial services

We are committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Response time7 hrs
Response rate88%
Recommended by100%of homeowners
Showing 1-10 of 48
Welding questions, answered by experts

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

The Stedman, NC homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.

What do you need done? We’ll find top pros.
  • 🌱 "Mow a small front yard"
  • 🛠 "Fix a leaking pipe under the sink"
  • 🏠 "Repair shingles on an asphalt roof"