Top-rated well and pump technicians.

Best well and pump technicians near Lansing, NC

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Lansing, NC?

Select your specific project to find the pro for you.

TRUSTED BY LANSING, NC HOMEOWNERS

  • Average homeowner rating star icon4.8
    Average homeowner rating
  • Verified reviews icon10
    Verified well and pump services reviews

Top-Rated Well and pump technicians in Lansing - Updated Nov 2026

Dobys Plumbing and Repair, Inc.
4.2(
11
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Lansing, NC and surrounding areas

In business since 2008

Free estimates

Credit card accepted

"On Friday, January 21, 22, our water pressure was minimal. Got a referral from Robert A. Holman. Called Doby at 4pm. They arrived before 5pm. Professional, polite and offered assistance that evening. Forecasted temp was to be 19 degrees. We said tomorrow was fine. Said they’ll come at 9:00a. Arrived on time. Pump is 400ft. Pulled the pump. Diagnosis-wire was frayed. Gave us 2 options. (Pump was installed in 2005) Could repair wire or replace pump. (easily could of said pump was bad) I wouldn’t of known if it was bad or good. Jonathan and Chris were honest and professional. We decided to replace the pump. By 2pm, job completed. Entire area was cleaned. When Jonathan gave us the invoice, he explained all details. Today, is January 23. No issues. SO impressed with everyone, from the lady who answered our call, to Jonathan and Chris. I recommend DOBY 110%."
Response time1 day
Recommended by87%of homeowners
Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,680
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Lansing, NC and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
C&C land clearing and excavation
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Lansing, NC and surrounding areas

With over 10 years of experience, C&C Land Clearing and Excavation is your go-to contractor for excavation, trenching, and drainage solutions in the Tri Cities and western North Carolina area . We understand the importance of building a solid foundation and offer expert land clearing and dirt work to set your project up for success. We are known for our responsiveness, fair pricing, and high-quality results. Your site will be handled with care and precision.

Wells and Pumps FAQs, answered by experts

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

There are many signs to look for that will tell you when your irrigation pump is burned out. This may include low water pressure, sprinklers that sputter a lot before turning on, discolored or dirty water, or a pump that stops working altogether. If your pump has any of these issues, it is probably time to replace it.

Normally, when your well pump turns on or off, you’ll hear a small click. This isn’t anything to worry about, but it can be a problem if it’s clicking continuously. This can indicate that the well pump is short cycling—the pump continuously turns on and off.

This can wear out the motor and provide uneven water flow. If this happens, you may need to get it looked at by a well pump professional to see if you need to repair the switch or pump.

A shallow-well pump can pull water up to 25 feet deep. A deep-well pump can pull water up to 90 feet deep. A deep-well submersible pump can pull water up to 300 feet deep. Make sure to consult a pro to find out how deep your well is and get the right pump for your needs.

If you notice that your well pump runs continuously, it’s important to take action quickly to avoid further damage. A few common issues may be to blame for a continuously running well pump, such as mechanical damage, a faulty pressure control switch, low water level, prime loss, and leaking pipes and fixtures.

The Lansing, NC homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.