Top-rated well and pump technicians.

Get matched with top well and pump technicians in Circle, MT

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Circle, MT?

Select your specific project to find the pro for you.

Find Well and pump technicians in Circle

Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,678
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Circle, MT and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"Went well to this point of replacing parts. Then the United needed to have a system leak test and then needed freon put in pump. This was refused by Choice warranty. We were left with a partial repair and a heat pump not able to do it's job."
Recommended by81%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Circle, MT and surrounding areas

In business since 1971

Credit card accepted

"Called AHS....who sent service request to AAA Flexible Pipe. Adam came out quickly and installed new pump just before HEAVY rains hit...Fast and efficient service from AHS and AAA FLEXIBLE PIPE CLEANING."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Avatar for TCH Builders & Remodeling
TCH Builders & Remodeling
4.0(
2
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Circle, MT and surrounding areas

In business since 1999

Emergency services offered

Credit card accepted

If you dream it, we can build it. What's the biggest difference between us and them? We build to last! We offer a full line of Green and Energy Star Certified products, backed by our labor and manufacturer's lifetime transferable warranties. Credit Cards Welcome Financing Available OAC.

Recommended by100%of homeowners
Request Quote
Swift Services
New to Angi
Well Pump - Install or Replace

Serving Circle, MT and surrounding areas

In business since 2020

Free estimates

Offers commercial services

Swift Handyman Services is your one stop shop for all of your Handyman needs! We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business. Give us a call today! Swift Handyman Services\n \n\n\n

Request Quote
Wells and Pumps questions, answered by experts

A well pressure tank is located between the well and the well pump, and it stores your water under pressure so that the well pump can eventually do its job. The well pump is activated whenever you turn a faucet on—it pulls the water from the tank into your home. Both are vital parts of a complete well water system.

Several warning signs can indicate current or future issues with your well pressure tank. If you notice inconsistent water pressure, water spitting from your faucets, clicking sounds, or electricity bill spikes without other obvious causes, it may be time to get your pressure tank and well system looked at by a professional.

If you notice that your well pump runs continuously, it’s important to take action quickly to avoid further damage. A few common issues may be to blame for a continuously running well pump, such as mechanical damage, a faulty pressure control switch, low water level, prime loss, and leaking pipes and fixtures.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Yes, you can adjust your well pump pressure relatively easily by yourself. You’ll need to remove the cover from your pressure switch and adjust a nut that controls cut-in pressure. Learn more about how to adjust a well pump pressure switch with a step-by-step guide to setting your water pressure.

The Circle, MT homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles